16/04/2024 02:15:05

Motor - Seat Track - Passenger Seat (Remove and Replace)

Correction code 1301020202 FRT 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Seat base edges are sharp and can cause personal injury. Wear cut resistant gloves when removing the seat from the vehicle, and while performing procedures that involve work on or near the seat base.

Remove

  1. Open all doors and lower all windows.
  2. Remove the RH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  3. Remove the RH middle A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  4. Use a clip prytool to release the RH front seat harness from the sill trim clips (x4).
  5. Pull the RH front seat harness from under the RH front cabin carpet.
  6. Move the RH front seat forward, and then remove and discard the RH front seat rear bolts (x2).
  7. Move the RH front seat backward, and then remove and discard the RH front seat front bolts (x2).
  8. Tilt the RH front seat rearward.
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to disconnect the RH seat harness from the body controller. Take care when moving the seat. Ensure the carpet is not damaged.
  9. Remove and discard the bolts (x2) that attach the RH seat track motor to the seat cushion frame.
  10. Disconnect the electrical harness from the RH seat track motor connector.
  11. Remove harness clip from seat track motor bridge assembly.
  12. Release the inboard track from the track motor bridge.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pry up on the track motor bridge tab and slide the outboard track away to release.
  13. Release the track motor bridge from the outboard track.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pry up on the track motor bridge tab and slide the track motor bridge away from the inboard track.

Install

  1. Install the RH front seat outer track onto the track bridge assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    The track motor cable is keyed square and must be aligned with the inner track. Turn the cable by hand to align as needed. Slide the track motor bridge into the inboard track till it is fully and securely seated.
  2. Install the track motor bridge to the inner track.
    Informational PurposesAn informational icon, calling your attention
    Note
    The track motor cable is keyed square and must be aligned with the inboard track. Turn the cable by hand to align as needed. Slide the track motor bridge into the inboard track till it is fully and securely seated.
  3. Connect the track motor electrical connector.
  4. Install the harness clips (x3) to the RH front seat track motor.
  5. With assistance, install the bolts (x2) that attach the RH side track assembly to the RH front seat cushion assembly.
    23 Nm (17.0 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T50 Bit Stubby
    • 3 in extension
    • Flex head ratchet/flex head torque wrench
    • Cordless Ratchet/Impact Driver
  6. Reposition the RH front seat onto the RH front seat risers.
    Informational PurposesAn informational icon, calling your attention
    Note
    Take care when moving the seat. Ensure the carpet is not damaged.
  7. Secure the RH front seat harness under the RH front cabin carpet.
  8. Install the RH front seat harness to the sill trim clips (x3).
  9. Move the RH front seat forward, and then install new RH front seat rear fasteners (x2).
    33.5 Nm (24.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • Cordless Ratchet/Impact Driver
    • Flex head ratchet/flex head torque wrench
  10. Move the RH front seat backward, and then install new RH front seat front fasteners (x2).
    33.5 Nm (24.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • Cordless Ratchet/Impact Driver
    • Flex head ratchet/flex head torque wrench
  11. Install the RH middle A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  12. Install the RH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  13. Move the RH front seat to original position.
  14. Raise all windows and close all doors.