26/07/2024 11:51:38

Cap - Brightwork - Upper - LH (Remove and Replace)

Correction code 1220010072 FRT 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Cap - Brightwork - Upper - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Screws (x5) that attach the front portion of the LH upper brightwork to the body
1.1 Nm (.8 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 2 in extension
  • Torx T20 socket
  • Ratchet/torque wrench
 Reuse
Screws (x3) that attach the rear portion of the LH upper brightwork to the body
1.1 Nm (.8 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 2 in extension
  • Torx T20 socket
  • Ratchet/torque wrench
 Reuse

Remove

  1. Remove the LH B-pillar applique. See Applique - B-Pillar - LH (Remove and Replace).
  2. Remove the fir tree clips (x2) that attach the primary body seals to the vehicle.
  3. Pull down to release the front and rear primary body seals from the LH upper brightwork.
    Informational PurposesAn informational icon, calling your attention
    Note
    Start from the upper corner closest to the B-pillar applique, and then pull straight down along the length of the seal to fully release the seal from the upper brightwork.
  4. Remove the screws (x5) that attach the front portion of the LH upper brightwork to the body.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 2 in extension
    • Torx T20 socket
    • Ratchet/torque wrench
  5. Remove the push rivet that attaches the front of the LH upper brightwork to the body.
  6. Remove the screws (x3) that attach the rear portion of the LH upper brightwork to the body.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 2 in extension
    • Torx T20 socket
    • Ratchet/torque wrench
  7. With assistance, remove the LH upper brightwork from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Start from the front of the trim and work rearward. The rear of the trim engages the rear quarter glass.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Be careful not to damage paint and/or quarter glass when removing the trim.
  8. Remove and discard the grommets (x9) from the body.

Install

  1. Install new grommets (x9) into the body where the LH upper brightwork will install.
  2. With assistance, carefully position the LH upper brightwork onto the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Starting at the rear quarter glass, ensure the bright trim is fully seated on the dowel protruding out of the rear quarter glass.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Be careful not to damage paint and/or quarter glass when removing the trim.
  3. Install the push rivet that attaches the front of the LH upper brightwork to the body.
  4. Install the screws (x5) that attach the front portion of the LH upper brightwork to the body.
    1.1 Nm (.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 2 in extension
    • Torx T20 socket
    • Ratchet/torque wrench
  5. Install the screws (x3) that attach the rear portion of the LH upper brightwork to the body.
    1.1 Nm (.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 2 in extension
    • Torx T20 socket
    • Ratchet/torque wrench
  6. Press up to fasten the rear and front primary body seals onto the LH upper brightwork.
    Informational PurposesAn informational icon, calling your attention
    Note
    Work from the rear corner of each seal forward, and make sure that the seal fully engages the brightwork. When installed correctly, the seal edge is not visible.
  7. Work each seal around the opening so as to evenly distribute it.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure to push the seal into each corner.
  8. Install the fir tree clips (x2) that attach the primary body seals to the vehicle.
  9. Install the LH B-pillar applique. See Applique - B-Pillar - LH (Remove and Replace).