2025-03-04

Buckle - Seatbelt - 2nd Row - LH (Remove and Replace)

Correction code 2005020032 FRT 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • Torchless Heat Induction Tool - 2152873-00-A

Torque Specifications

Table 1. Torque Specifications: Buckle - Seatbelt - 2nd Row - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the LH buckle to the seat track
40 Nm (29.5 lbs-ft)
  • 3 in extension
  • 15 mm socket
  • Ratchet/torque wrench
  • Flex head ratchet/flex head torque wrench
  • Torchless Heat Induction Tool - 2152873-00-A (for removal only)
 Replace

Remove

  1. Remove the 2nd row lower seat cushion. See Seat Cushion - 2nd Row (Remove and Replace).
  2. Disconnect the LH rear seat belt buckle electrical connector.
  3. Release the plastic bracket that attaches the female side of the electrical connector to the body studs.
  4. Remove and discard the bolt that attaches the LH 2nd row buckle to the body, and then remove the buckle from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    If the bolt is hard to remove, use an inductive heating tool to melt the adhesive patch material. Position the inductive heating tool coil around the bolt, and then heat the bolt for 20 seconds. Allow the bolt to cool down for 2 minutes, and then remove and discard the bolt. The inductive heater coil, bolt, and adjacent areas will be extremely hot.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Persons that have a pacemaker or any other kind of electronic or metal surgical implant must stay at least 1 m (3 ft) away from the inductive heater while it is in use.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Remove all metallic items (such as coins, keys, electronics, and tools) from pockets before using the inductive heater.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Ensure that there is a properly-maintained fire extinguisher in the work area before using the inductive heater.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Use the inductive heater in a well-ventilated area.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 3 in extension
    • 15 mm socket
    • Ratchet/torque wrench
    • Flex head ratchet/flex head torque wrench
    • Torchless Heat Induction Tool - 2152873-00-A (for removal only)

Install

  1. Install new bolt that attaches the LH seat buckle to the body.
    40 Nm (29.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the guide pin is aligned.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 3 in extension
    • 15 mm socket
    • Ratchet/torque wrench
    • Flex head ratchet/flex head torque wrench
    • Torchless Heat Induction Tool - 2152873-00-A (for removal only)
  2. Install the plastic bracket that attaches the female side of the electrical connector to the body studs.
  3. Connect the LH rear seat belt buckle electrical connector.
  4. Install the 2nd row lower seat cushion. See Seat Cushion - 2nd Row (Remove and Replace).