17/10/2023 18:48:51

Hood Hinges And Fittings - Active Hood Hinge, LH (Remove and Replace)

Correction code 1133030072 FRT 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Remove

  1. Remove the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Replace).
  2. Remove the cabin intake duct. See Cabin HVAC - HVAC, Fresh Air Gutter, Assembly (Remove and Replace).
  3. Remove the access panel. See Front Bumper Fascia - Assembly, Access Panel (Remove and Replace).
  4. Remove the underhood storage unit. See Exterior Fittings - Luggage Compartment Trim - Front Luggage Storage Compartment - Frunk Assembly (Remove and Replace).
  5. Remove the LH and RH wiper arms and blades. See Electrical - Wipers and Washers - Windshield Wipers and Motor - Wiper Arm DR (Remove and Replace).
  6. Remove the LH and RH hood hinge covers. See Hood Hinges And Fittings - Hood Hinge Cover LH (Remove and Replace)
  7. Remove the LH and RH shock tower covers. See Underhood Trim -Shock Tower Cover LH (Remove and Install).
  8. Remove the cowl screen panel. See Underhood Trim - Assembly, Cowl Screen, LHD (Remove and Replace).
  9. Remove the wiper motor. See Electrical - Wipers and Washer - Windshield Wipers and Motor - Wiper Module (Remove and Replace).
  10. Remove the hood. See Hood Assembly \(Remove and Replace\).
  11. Use tape to mark the mounting location of the hinge on the body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  12. Remove the bolts (x2) that attach the LH hood hinge to the body, and then remove the hinge from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 13 mm socket
    • Ratchet/torque wrench

Install

  1. Position the LH hood hinge into the vehicle.
  2. Install the bolts (x2) that attach the LH hood hinge to the body.
    24 Nm (17.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use the masking tape to aid in alignment. Adjust the hood hinge as needed.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • 13 mm socket
    • Ratchet/torque wrench
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  3. Remove the masking tape from the LH hinge location.
  4. With an assistant, install the hood. See Hood Assembly \(Remove and Replace\).
  5. Install the wiper motor. See Electrical - Wipers and Washer - Windshield Wipers and Motor - Wiper Module (Remove and Replace).
  6. Install the cowl screen panel. See Underhood Trim - Assembly, Cowl Screen, LHD (Remove and Replace).
  7. Install the LH and RH shock tower covers. See Underhood Trim -Shock Tower Cover LH (Remove and Install).
  8. Install the LH and RH hood hinge covers. See Hood Hinges And Fittings - Hood Hinge Cover LH (Remove and Replace)
  9. Install the LH and RH wiper arms and blades. See Electrical - Wipers and Washers - Windshield Wipers and Motor - Wiper Arm DR (Remove and Replace).
  10. Install the underhood storage unit. See Exterior Fittings - Luggage Compartment Trim - Front Luggage Storage Compartment - Frunk Assembly (Remove and Replace).
  11. Install the access panel. See Front Bumper Fascia - Assembly, Access Panel (Remove and Replace).
  12. Install the cabin intake duct. See Cabin HVAC - HVAC, Fresh Air Gutter, Assembly (Remove and Replace).
  13. Install the rear underhood apron. See Underhood Trim - Rear Apron Assembly (Remove and Replace).