07/07/2024 18:43:46

Panel - Door Trim - Front - LH (Remove and Install)

Correction code 1513010011 FRT 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Table 1. Torque Specifications: Panel - Door Trim - Front - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Screws (x3) that attach the LH front door panel to the LH front door
6 Nm (4.4 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • Torx T30 socket
  • 6 in extension
  • Ratchet/torque wrench
 Reuse

Remove

  1. Open the front LH door, and fully lower the window.
  2. Remove the reflector from the rear edge of the LH front door trim panel.
  3. Remove the screws (x3) that attach the trim panel to the door.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • Torx T30 socket
    • 6 in extension
    • Ratchet/torque wrench
  4. Remove the front LH door tweeter. See Tweeter - Front Door - LH (Remove and Replace).
  5. Remove the LH front door puddle light. See Puddle Lamp - Front Door (Remove and Replace).
  6. Pull out on the trim panel from the puddle light opening to release the clips that attach the trim panel to the door.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not remove the trim panel from the door at this time.
  7. Continue to pull and release all of the clips around the edge of the trim panel, working from the bottom up.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not remove the trim panel from the door at this time.
  8. Release the manual release cable from the cable bracket and then remove the cable collar from the trim panel and pivot the collar down to a vertical orientation.
  9. Slide the cable barrel end out of the release lever, and remove the cable from the trim panel.
  10. Disconnect the electrical harness from the door connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not remove the trim panel from the door at this time.
  11. Raise the trim panel up to unhook it from the door, and then remove the panel from the door.
  12. Check the LH front door for any remaining push clip retainers, and if present, remove them from the door.

Install

  1. Install the underside puddle light to the LH front door panel. See Puddle Lamp - Front Door (Remove and Replace).
  2. Bring the trim panel to the door, and rest it on the door edge.
  3. Connect the electrical harness to the LH front door connector.
  4. Position the manual release cable in a vertical orientation, and slide the cable barrel end into the release lever.
  5. Pivot the manual release cable collar to a horizontal orientation and press the collar into the trim panel, and then secure the cable to the cable bracket.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the manual release cable is routed underneath the door harness.
  6. Lift the trim panel, compress the LH front door inner belt seal slightly, and then hook the three trim panel tabs into the top edge of the door.
  7. Fasten the clips that attach the trim panel to the door.
  8. Make sure that the trim panel fits tightly, and that there are no gaps from misaligned or bent clips.
  9. Install the screws (x3) that attach the trim panel to the door.
    6 Nm (4.4 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Make sure that all fasteners are properly torqued and not cross-threaded.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • Torx T30 socket
    • 6 in extension
    • Ratchet/torque wrench
  10. Install the reflector to the rear edge of the trim panel.
  11. Install the front LH door tweeter. See Tweeter - Front Door - LH (Remove and Replace).
  12. Close the door and verify the operation of the manual door release lever, that the door latch releases smoothly and easily.
  13. Raise the LH front window and close the door.