NVH Pad - HV Battery (Remove and Replace)
Correction code 1601010102 FRT 3.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.
Remove
-
Remove bolts securing LH rocker panel
lower cover to body.
Note4x bolts, 10mm, 5 Nm, Release 4x covers to access bolts, The number of fasteners on newer vehicles may vary.
-
Remove clips securing the LH rocker
panel lower cover to wheel liners.
Note4x push clips.
-
Remove LH rocker panel lower
cover.
Note10x clips.
-
Remove bolts securing RH rocker panel
lower cover to body.
Note4x bolts, 10mm, 5 Nm, Release 4x covers to access bolts, The number of fasteners on newer vehicles may vary.
-
Remove clips securing the RH rocker
panel lower cover to wheel liners.
Note4x push clips.
-
Remove RH rocker panel lower
cover.
Note10x clips.
-
Open all four doors.
NoteIf vehicle is being powered down, Latch rear doors to prevent accidental closure.
-
Lower all four windows.
- Move LH front seat backward.
-
Remove LH front floor mat.
-
Partially release LH front primary
door seal.
NoteRelease the lower section of LH front primary door seal.
-
Remove LH IP end cap.
Note5x clips, 2x guide tabs.
-
Remove clip securing LH lower A-pillar
assembly.
Note1x push clip.
-
Remove LH lower A-pillar
assembly.
Note4x clips, 2x guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release front tabs from carpet.
-
Release LH footwell cover.
Note5x clips,1x guide tab.
-
Disconnect LH footwell cover
connectors.
Note2x connectors.
-
Remove LH console side panel
carpet.
Note11x clips, 2x positioning clips, 1x tab, Use trim tool starting at rear edge to release upper clips, If the clip is too tight, Use prytool to remove the clips, Then pull bottom to release remaining clips, Finally, release the tab and pull out the side panel backward, Replace the clips if it is damaged.
-
Remove LH front main cabin carpet
clips.
Note2x push clips, Number of clips on new vehicles may vary.
-
Fold the LH front main cabin carpet
aside for access.
NoteDead pedal and foam block are part of carpet,.
-
Remove LH front footwell HV battery
bolts.
Note2x bolts, EP20, 136 Nm.
- Move LH front seat forward.
-
Move RH front seat backward.
-
Remove RH front floor mat.
-
Partially release RH front primary
door seal.
NoteRelease the lower section of RH front primary door seal.
-
Remove RH IP end cap.
Note5x clips, 2x guide tabs.
-
Remove clip for RH lower A-pillar
trim.
Note1x push clip.
-
Remove RH lower A-pillar trim.
Note4x clips, 2x guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release front tabs from carpet.
-
Release RH footwell cover.
Note2x magnets, 1x guide tab, 1x connector.
-
Remove connectors from RH footwell
cover.
Note1x puddle light connector, 1x Speaker connector.
-
Remove RH console side panel
carpet.
Note12x clips, 2x positioning clips, 1x datum, Use trim tool starting at rear edge to release upper clips, If the clip is too tight, Useprytool to remove the clips, Then pull bottom to release remaining clips, Finally, release the datum and pull out the side panel backward, Replace the clips if it is damaged.
-
Remove clips securing RH front main
carpet to vehicle.
Note1x clip, Number of clips on new vehicles may vary.
-
Fold RH front main cabin carpet aside
for access.
Note2x clips, Lift center piece and pull carpet back, Release seat harness from clips to allow carpet to fold back more.
-
Remove RH front footwell HV battery
bolts.
Note2x bolts, EP20, 136 Nm.
-
Move RH front seat forward.
-
Close RH front door.
-
Remove 2nd row floor mat from
vehicle.
-
Release 2nd row seat cushion and
disconnect harness.
Note2x clips, 2x connectors, Press tabs backward then pull front edge up.
-
Pull back rear carpet to access rear
interior battery bolts.
Note2x push clips.
-
Remove LH rear HV battery interior
bolt.
Note1x bolt, 16mm, 66 Nm, Lift up carpet for access.
-
Close LH rear door latch
manually.
-
Remove RH rear HV battery interior
bolt.
Note1x bolt, 16mm, 66 Nm, Lift up carpet for access.
-
Close RH rear door latch
manually.
-
Raise and support vehicle.
NoteRemove body plugs and install M3 lift pad adapters to indicated locations .
-
Place vehicle in service mode
plus.
NoteUsing Vehicle Ops mobile app enter last six digits of VIN then select vehicle from list then swipe to the left and select "Enable Service Mode Plus"Vehicle Ops mobile app can be downloaded at: https://mobile.tesla.com/AppStore/Home/AppDetails?appId=6.
-
Unlock vehicle gateway.
NoteAfter vehicle has been put into "Service Mode", place keycard on center console to turn on drive rails, hold down the brake pedal, while keep pressing right hand signal button simultaneously for at least 10 seconds, "GTW UNLOCKING" should pop up on the UI right next to the VIN during these 10 seconds, once gateway is unlocked "GTW UNLOCKED 5400" will be displayed on the UI next to the VIN, the gateway will remain unlocked for 90 minutes, follow steps on Toolbox article #5582900 for any additional information.
-
Run Thermal Fill Drain (Coolant Only)
through the UI.
NoteSelect Thermal > Coolant System > Coolant Fill/Drain, click Run, close once routine is completed, Thermal Fill Drain routine has a 5 hour time limit, After 5 hours routine must be performed again.
- Open hood.
-
Remove rear underhood apron.
Note14x clips.
-
Power off vehicle from center
display.
NoteVia Controls > Safety > Power Off, Select Power Off button at warning dialogue box.
-
Disconnect LV battery and First
Responder Loop.
Note2x connectors, Release green locking tab, Press black tab then pull black connector lock outwards to release connection, Release red lock tab on FRL, Allow 2 minutes for all electrical circuits to fully discharge.
-
Remove all items from pockets and
ensure not wearing metal items.
-
Verify operation of multimeter.
NoteSet multimeter to DC voltage, Confirm multimeter is properly measuring voltage by testing the 16v battery.
-
Inspect HV insulating gloves.
NoteCheck gloves for damage prior to use, Refer to service document TN-15-92-003 R1, for information on inspecting HV gloves.
-
Put on HV insulating gloves and
leather over gloves.
NoteMake sure to wear Electrical Protective Gloves any time Hioki tester is used.
-
Remove bolts securing ancillary bay probe
lid cover to ancillary bay cover.
Note2x bolts, EP10 5-Lobe, 6 Nm, Discard after removal.
-
Remove ancillary bay probe lid cover from
ancillary bay cover.
-
Verify no high voltage.
NoteMake sure to wear PPE (HV gloves, safety glasses) when working on high voltage component, If voltage is greater than 10V, Pack contactors are not open or welded, Stop work and reach out to Service Engineering.
-
Inspect ancillary bay probe lid cover
gasket then position onto the ancillary bay cover.
NoteConfirm no visual damage present,Wipe ancillary bay with IPA to clean surface,Allow to 1 minute dry time.
-
Install bolts securing ancillary bay probe
lid cover to ancillary bay cover.
Note2x bolts, E10 5-Lobe, 6 Nm, Install new fasteners.
-
Remove fastener securing busbar cover
access door.
Note1x bolt, 10mm, 9 Nm.
-
Remove bolts securing charge port
busbar kit to HV header.
Note2x bolts, 10mm, 9 Nm.
-
Lift busbar kit connector to remove
from HV header.
Note4x guide tabs, Ease removal of aluminum connector housing by shifting rear end of busbar assembly upward.
-
Remove HV insulating gloves.
-
Disconnect HVC logic connector and
install logic cap.
Note1x connector, 1x cap, Release locking tab then push the handle downward to release connector.
-
Remove bolt securing DCDC ground
busbar to body.
Note1x bolt, 12mm, 20 Nm.
-
Remove nut securing DCDC ground busbar
to HV battery.
Note1x nyloc nut, 13mm, 9 Nm, Discard nut after removal.
-
Remove DCDC ground busbar.
-
Remove nut securing positive LV output
from PCS cable and move cable aside.
Note1x nut, 13mm, 15 Nm, Discard after removal.
-
Raise vehicle fully and lower lift
onto locks.
NoteSet vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side, Verify doors are clear of surrounding objects.
-
Remove LH and RH clips securing rear
aero shield to wheel house liner.
Note2x clips.
-
Remove rear aero shield.
Note11x bolts, 10mm, 5 Nm.
-
Remove outer fasteners securing front
aero shield.
Note7x bolts, 10mm, 5 Nm.
-
Remove remaining nuts and remove front
aero shield from vehicle.
Note2x nuts, 15mm, 5 Nm.
-
Remove push clips securing lower rear
edge of LH front wheel liner to vehicle for access to coolant hose.
Note3x push clips.
-
Remove bolt securing LH front wheel
liner to skid plate.
Note1x bolt, 10mm, 5 Nm.
-
Use bungee strap to pull back LH front
wheel liner.
NoteSecure to subframe.
-
Position coolant drain container
underneath LH front of HV battery.
-
Attach hose extension to coolant drain
hose for extra length.
-
Connect battery flush fitting adapter
to coolant cart drain hose.
-
Disconnect HV battery return hose at
LH side of vehicle and connect battery flush fitting to male side.
Note1x spring clip.
-
Attach battery drain fitting adapter
to female side of HV battery return tube.
Note1x spring clip, Make sure valve is set to closed, Perform push-pull test to verify adapter is fully engaged.
-
Attach battery drain fitting adapter
to coolant cart pressure hose.
-
Open valve on battery drain fitting
adapter.
NoteTurn valve knob to vertical position.
-
Slowly open valve on pressure
regulator and allow coolant to drain out of HV battery return tube.
NoteClose valve on pressure regulator once no coolant is draining from HV battery return hose.
-
Close valve on pressure regulator once
no coolant is draining from battery return hose.
-
Disconnect compressed air from coolant
cart.
-
Remove battery drain fitting adapter
from female side of HV battery return tube.
Note1x spring clip, Set valve knob to closed position.
-
Remove battery flush fitting adapter
from male side of HV battery return tube.
Note1x spring clip, Plug hose once adapter has been removed.
-
Remove bolt securing RH front wheel
liner to skid plate.
Note1x bolt, 10mm, 5 Nm.
-
Remove push clips securing lower rear
edge of RH front wheel liner to vehicle for access to coolant hose.
Note3x push clips.
-
Use bungee strap to pull back RH front
wheel liner.
NoteSecure to subframe.
-
Position coolant drain container
underneath RH front of HV battery.
-
Disconnect powertrain supply hose from
powertrain supply tube.
Note1x spring clips, Plug hoses as required.
-
Disconnect powertrain return hose from
powertrain return tube.
Note1x spring clip, Plug hoses as required.
-
Disconnect HV battery manifold
hose.
Note1x spring clip, 2x plugs, Plug hoses as required.
-
Remove bolts securing front skid
plate.
Note4x bolts, EP10, 13 Nm.
-
Remove skid plate from HV
battery.
-
Disconnect A/C compressor HV harness
connector.
Note1x connector, 1x Red locking tab, 2 stage push release, Unlock by pulling back red tab, Push orange lip and pull back ''stage 1'', Push green lip and pull back to disconnect.
-
Release LH side hose clip from rear
battery skid plate enclosure.
Note1x fir tree clip.
-
Release RH side hose clips from rear
battery skid plate enclosure.
Note2x fir tree clips.
-
Remove lower bolts securing HV battery
rear skid plate enclosure .
Note2x bolts, EP10, 13 Nm, Older vins may be equipped with additional fastener count.
-
Remove upper nut securing HV battery
rear skid plate enclosure .
Note1x nut, 10mm, 13 Nm, Fastener count may vary on older built vehicles.
-
Remove upper bolts securing HV battery
rear skid plate enclosure .
Note4x bolts, 13mm, 35 Nm.
-
Remove HV battery rear skid plate
enclosure .
-
Position coolant drain container
underneath LH rear of HV battery.
-
Disconnect LH coolant hose from rear
of HV battery.
Note1x spring clip, 2x plugs, Plug both the coolant hose and passthrough .
-
Remove fir tree clip securing coolant
hose to rear subframe shear plate.
Note1x fir tree clip.
-
Disconnect RDU inverter inlet tube
from LH rear of HV battery.
Note1x spring clip, Plug hose connections as needed, Coolant loss greater than 1 L will require vacuum fill.
-
Attach coolant drain hose adapter to
PCS outlet hose coupling.
NoteUse adapter with 90 degree angle, Make sure locking tab is fully seated.
-
Attach coolant drain hose adapter to
coolant hose extension.
-
Attach coolant hose extension to
coolant drain hose.
NoteUse caution as coolant may spill, Make sure to wear safety glasses.
-
Position coolant drain container
underneath RH rear of vehicle.
-
Disconnect rear PT supply hose from
rear of HV battery.
Note1x spring clip, Plug hose connections as needed, Coolant loss greater than 1 L will require vacuum fill.
-
Attach coolant pressure tester to PCS
inlet hose coupling.
NoteThis adapter connected to regulated air line adapter, Make sure the locking tab is fully seated.
-
Attach coolant pressure tester to
pressure fitting adapter.
-
Connect compressed air to coolant
pressure tester.
-
Open regulator valve then slowly
adjust regulator to 50 psi.
NoteUse caution as coolant may spill, Make sure to wear safety glasses.
-
Open 2nd valve slowly.
NoteUse caution as coolant may spill, Make sure to wear safety glasses.
-
Set timer for 1 minutes and select
start.
NoteOnce timer is complete, select Stop Reset.
-
Close regulator valve.
-
Disconnect compressed air from coolant
pressure tester.
-
Remove coolant pressure tester from
PCS inlet hose coupling.
-
Position coolant drain container
underneath LH rear of HV battery.
-
Remove coolant drain adapter with hose
from PCS outlet hose coupling.
Note1x spring clip.
-
Disconnect RDU outlet hose from PT
return tube and plug both hose ends.
Note1x spring clip, 2x plugs, Lower hose located at RH rear of HV battery, Use shop towel to clean any residue coolant if necessary, Coolant loss greater than 1 L will require vacuum fill.
-
Support front portion of rear
subframe.
-
Release clips securing coolant hoses
to LH shear plate.
Note2x fir tree clips.
-
Remove smaller fasteners securing LH
shear plate.
Note2x bolts, 13mm, 35 Nm.
-
Remove large bolt securing LH shear
plate and subframe to body and remove shear plate.
Note1x bolt, 21mm, 130 Nm, Discard after removal.
-
Hand tighten bolt securing LH side of
subframe to body.
Note1x bolt, 21mm, 130 Nm.
-
Release clips securing coolant hoses
to RH shear plate.
Note2x fir tree clips.
-
Remove smaller fasteners for RH shear
plate.
Note2x bolts, 13mm, 35 Nm.
-
Remove large bolt securing RH shear
plate and subframe to body and remove shear plate.
Note1x bolt, 21mm, 130 Nm, Discard at later step.
-
Hand tighten bolt securing RH side of
subframe to body.
Note1x bolt, 21mm, 130 Nm.
-
Remove support stand from under
vehicle.
-
Remove nut securing RDU HV cable
bracket to HV battery.
Note1x nut, 10mm, 10 Nm, Number of fasteners may vary.
-
Disconnect RDU HV cable from HV
battery.
Note1x connector, Release locking tab and rotate the release lever up to disengage the connector, Do not force the release lever up, Ensure the alignment tabs on the RDU header are not damaged.
-
Place HV battery table into position
and lower vehicle to support HV battery.
NoteRecommend assistance, Line up table so center 4 bolts are accessible through opening in table, Adjust final battery table position using adjustable caster jacks on table.
-
Remove central bolts securing HV
battery center ski cover.
Note4x bolts, EP14, 34 Nm.
-
Remove bolts securing LH front support
bracket to vehicle.
Note4x bolts, 16mm, 110 Nm.
-
Remove bolts securing RH front support
bracket to vehicle.
Note4x bolts, 16mm, 110 Nm.
-
Remove LH bolts securing HV battery to
vehicle.
Note8x bolts, 13mm, 35 Nm.
-
Remove RH bolts securing HV battery to
vehicle.
Note8x bolts, 13mm, 35 Nm.
-
Raise vehicle free of HV
battery.
NoteRecommend assistance.
-
Remove battery from under
vehicle.
NoteRecommend assistance.
-
Remove NVH pads.
Note4x NVH pads, Use of a non marring scraper assists in removal.
-
Clean surface area with IPA.
NoteAllow for 1 minute dry time for IPA, Verify no debris is present.
Install
-
Measure 180mm from base of hump and mark locations for installation of NVH
pads.
NoteApply tape to mark location.
-
To ensure NVH pads are centered at each location, Measure from side of pack to
nearest protrusion, Then from protrusion to center channel.
NoteApply tape to mark location, This will help align NVH pads while installing.
-
Install NVH pads onto HV battery pack.
Note4x NVH pads, Start from marked end and slowly install strip while pulling away tape backing, Verify foam strip is centered prior to applying pressure, Wet out foam strip using pressure roller to ensure full application .
-
Install HV battery alignment rods.
Note2x rods, To body at front of vehicle, 2x rods, To battery near ancillary bay.
-
Position HV battery under vehicle.
NoteRecommend assistance.
-
Lower vehicle onto HV battery and align holes.
NoteRecommend assistance, Use alignment rods, Be sure coolant hoses do not get caught on alignment rods, Caution not to damage HV cable, Do not fully lower vehicle onto battery (this will help with installing battery bolts).
-
Set RH bolts securing HV battery to vehicle with cordless impact.
Note8x bolts, 13mm, 35 Nm, Ensure smooth thread engagement and bolts are not cross threaded into casting, Flush down bolts, Do not over tighten bolts, Fully torque at later step.
-
Set LH bolts securing HV battery to vehicle with cordless impact.
Note8x bolts, 13mm, 35 Nm, 8x bolts, 13mm, 35 Nm, Ensure smooth thread engagement and bolts are not cross threaded into casting, Flush down bolts, Do not over tighten bolts, Fully torque at later step.
-
Remove HV battery alignment rods.
Note2x rods, To body at front of vehicle, 2x rods, To battery near ancillary bay.
-
Set bolts securing RH front support bracket to vehicle with cordless impact.
Note4x bolts, 16mm, 110 Nm, 8x bolts, 13mm, 35 Nm, Ensure smooth thread engagement and bolts are not cross threaded into casting, Flush down bolts, Do not over tighten bolts, Fully torque at later step.
-
Set bolts securing LH front support bracket to vehicle with cordless impact.
Note4x bolts, 16mm, 110 Nm, 8x bolts, 13mm, 35 Nm, Ensure smooth thread engagement and bolts are not cross threaded into casting, Flush down bolts, Do not over tighten bolts, Fully torque at later step.
-
Set central bolts securing HV battery center ski cover with cordless impact.
Note4x bolts, EP14, 34 Nm, 8x bolts, 13mm, 35 Nm, Ensure smooth thread engagement and bolts are not cross threaded into casting, Flush down bolts, Do not over tighten bolts, Fully torque at later step.
-
Install bolts securing HV battery to body at LH shear plate area hand tight.
Note2x bolts, 13mm, 35 Nm, Torque at later step.
-
Install bolts securing HV battery to body at RH shear plate area hand tight.
Note2x bolts, 13mm, 35 Nm, Torque at later step.
-
Connect RDU HV cable to HV battery.
Note1x connector, Make sure the connector lock is 90 degrees from the connector before beginning to secure the connector, Use one hand to support the connector while other latching locking tab. Once installed, verify that the latch is not damaged and fully secured in the latched position.
-
Install nut securing RDU HV cable bracket to HV battery.
Note1x nut, 10mm, 10 Nm, Number of fasteners may vary.
-
Remove hose plugs and connect RDU outlet hose to PT return tube.
Note1x spring clip, 2x plugs, Perform push-pull-push test to make sure hose is fully engaged, Use shop towel to clean any coolant residue if necessary, Loss of coolant greater than 1L requires coolant vacuum fill.
-
Remove plugs and connect RDU inverter inlet hose to LH rear of HV battery.
Note1x spring clip, Perform push-pull-push test to make sure hose is fully engaged.Loss of coolant greater than 1L requires coolant vacuum fill.
-
Position HV battery rear skid plate enclosure onto HV battery for installation.
NoteRecommend assistance if needed.
-
Install upper bolts securing HV battery rear skid plate enclosure hand tight.
Note4x bolts, 13mm, 35 Nm, Torque at later step.
-
Install upper nut securing HV battery rear skid plate enclosure hand tight.
Note1x nut, 10mm, 13 Nm, Torque at later step.
-
Install lower bolts securing HV battery rear skid plate enclosure .
Note2x bolts, EP10, 13 Nm, Earlier vins may be equipped with additional bolts.
-
Lower vehicle onto pack completely.
NoteRecommend assistance.
-
Torque RH bolts securing HV battery to vehicle.
Note8x bolts, 13mm, 35 Nm.
-
Torque LH bolts securing HV battery to vehicle.
Note8x bolts, 13mm, 35 Nm.
-
Torque bolts securing RH front support bracket to vehicle.
Note4x bolts, 16mm, 110 Nm.
-
Torque bolts securing LH front support bracket to vehicle.
Note4x bolts, 16mm, 110 Nm.
-
Torque central bolts securing HV battery center ski cover.
Note4x bolts, EP14, 34 Nm.
-
Torque bolts securing HV battery rear skid plate enclosure to vehicle.
Note4x bolts, 13mm, 35 Nm.
-
Torque upper nut securing HV battery rear skid plate enclosure .
Note1x nut, 10mm, 13 Nm.
-
Torque lower bolts securing rear battery enclosure skid plate.
Note2x bolts, EP10, 13 Nm, Earlier vins may be equipped with additional bolts.
-
Install RH side hose clips to HV battery rear skid plate enclosure .
Note2x fir tree clips.
-
Install LH side hose clip to HV battery rear skid plate enclosure .
Note2x clips, Clip quantity may vary on older vehicles.
-
Raise vehicle and lower onto locks, then remove battery table from under
vehicle.
NoteRecommend assistance, Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side.
-
Support front portion of rear subframe.
-
Remove smaller fasteners for LH shear plate.
Note2x bolt, 13mm, 35 Nm.
-
Remove smaller fasteners for RH shear plate.
Note2x bolt, 13mm, 35 Nm.
-
Install LH front bolt and shear plate to rear subframe hand tight.
Note1x bolt, 21mm, 130 Nm, Install new bolt, Torque at later step.
-
Install bolts securing LH shear plate to HV battery hand tight.
Note2x bolts, 13mm, 35 Nm.
-
Install RH front bolt and shear plate to rear subframe hand tight.
Note1x bolt, 21mm, 130 Nm, Install new bolt, Torque at later step.
-
Install bolts securing RH shear plate to HV battery hand tight.
Note2x bolts, 13mm, 35 Nm.
-
Torque bolts securing shear plates to vehicle.
Note4x bolts, 13mm, 35 Nm.
-
Torque bolt securing subframe and LH shear plate to body.
Note1x front bolt, 21mm, 130 Nm, Mark bolt after torque.
-
Torque bolt securing subframe and RH shear plate to body.
Note1x front bolt, 21mm, 130 Nm, Mark bolt after torque.
-
Remove support stand from under vehicle.
-
Install clips securing coolant hoses to RH shear plate.
Note2x fir tree clips.
-
Install clips securing coolant hoses to LH shear plate.
Note2x fir tree clips.
-
lnstall rear aero shield.
Note11x bolts, 10mm, 5 Nm, Apply Loctite 222 onto rear aero shield bolts.
-
Install LH and RH clips securing rear aero shield to wheel house liner.
Note2x clips.
-
Connect HV battery manifold hose.
Note1x spring clip, Remove plugs.
-
Connect PT supply hose.
Note1x spring clip, Remove plugs, Perform push-pull-push test to make sure hose is fully engaged. Loss of coolant greater than 1L requires coolant vacuum fill.
-
Connect PT return hose.
Note1x spring clip, Remove plugs, Perform push-pull test to verify hoses are fully engaged. Loss of coolant greater than 1L requires coolant vacuum fill.
-
Install front skid plate.
Note4x bolts, EP10, 13 Nm, 2x tabs, Position and move backward to installation.
-
Release RH front wheel liner from bungee strap.
NoteRemove strap from vehicle.
-
Install bolt securing RH front wheel liner to skid plate.
Note1x bolt, 10mm, 5 Nm.
-
Connect HV battery return hose.
Note1x spring clip.
-
Release LH front wheel liner from bungee strap.
NoteRemove strap from vehicle.
-
Install bolt securing LH front wheel liner to skid plate.
Note1x bolt, 10mm, 5 Nm.
-
Connect A/C compressor HV harness connector.
Note1x connector, Engage locking tab.
-
Position front aero shield onto vehicle.
Note2x nuts, 15mm, 5 Nm, Hand-tighten the nuts to temporarily hold the panel in place.
-
Apply Loctite 222 onto front aero shield bolts and install outer fasteners to front
aero shield.
Note7x bolts, 10mm, 5 Nm.
-
Lower vehicle fully.
NoteRaise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered.
-
Remove coolant bottle cap.
-
Place empty coolant container into front storage area.
-
Fill container with at least 15L of coolant.
-
Place filled coolant container into front storage area.
-
Install refill tool cap onto coolant bottle assembly.
-
Setup vacuum refill tool.
NoteVerify all valves on refill tool are in the closed position, See image for clarity.
-
Install vacuum refill hose into refill cap on coolant bottle.
NotePerform push-pull-push test to verify hose is fully engaged.
-
Position overflow hose into empty container.
-
Place refill hose inside filled coolant container .
NoteMake sure hose end is fully submerged into coolant.
-
Connect shop air supply to coolant refill tool.
NoteIf not already done, Verify refill valve is set to off.
-
Open air inlet valve to draw a vacuum, Once gauge stabilizes, Fully close
valve.
NoteGauge stabilizes roughly (60-70 cmHg), Vacuum should not drop after the valves are closed.
-
Slowly open coolant refill valve to allow coolant to be drawn into coolant refill
hose, Close valve when hose is full of coolant.
NoteThis purges trapped air from the hose.
- Monitor gauge for 30 seconds to verify a vacuum is maintained in cooling system.
- Reopen the air inlet valve for 3 minutes to continue evacuating cooling system, then close valve.
-
Slowly open refill valve to allow coolant to be drawn into system.
NoteMake sure hose end of refill hose is fully submerged during entire process.
-
Once gauge reads zero, close refill valve.
-
Disconnect shop air supply from coolant refill tool.
-
Remove coolant refill hose from coolant container.
-
Remove coolant overflow hose from coolant container.
-
Remove vacuum refill hose from refill cap on coolant bottle.
-
Remove coolant refill tool from vehicle.
-
Remove both coolant containers from inside underhood area.
-
Position busbar kit connector and lower onto HV header.
Note4x guide tabs, Shift rear end of busbar assembly upward to help ease installation, If excessive force is required to seat busbars, they may have been bent. Inspect for damage and replace if necessary.
-
Install bolts securing charge port busbar kit to HV header.
Note2x bolts, 10mm, 9 Nm.
-
Install fastener securing busbar cover access door.
Note1x bolt, 10mm, 9 Nm.
-
Install DCDC ground busbar.
NoteSlotted hole goes to body side.
-
Install bolt securing DCDC ground busbar to body.
Note1x bolt, 12mm, 20 Nm.
-
Install nut securing DCDC ground busbar to HV battery.
Note1x nyloc nut, 13mm, 9 Nm, Install new nyloc nut.
-
Connect DCDC positive cable to right body harness.
Note1x connector,1x clip Connect the connector and push in the red locking tab.
-
Remove logic cap and connect HVC logic connector.
Note1x connector, 1x cap, Align connector then pull the handle to locking position get connector fully seated.
-
Connect First Responder Loop and LV battery.
Note2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated.
-
Remove lift arms from below vehicle.
NoteLower rack arms fully and remove them from under vehicle.
-
Move vehicle away from lift.
NotePosition to allow easy access to interior.
-
Select "Stop Thermal Fill Drain" through UI.
NoteAllow routine to complete, ensure routine is successful.
-
Inspect coolant level and top off as necessary.
NoteEnsure that fluid level is at Max line.
-
Select "Start Coolant Air Purge" using the UI.
NoteWait until coolant pumps stop running (audible noise), Routine Passed will appear, but pumps will run for 10 minutes, If you start next another routine during this time, it will fail, Make sure vehicle is not in "Drive", Routine is still running despite the completed message, Idle speed = ~1500 RPM, Test will vary speeds from 3500-6500 RPM and actuate valves between SERIES and PARALLEL, Putting vehicle into "Drive" will stop this routine, If speeds hover at 7000 RPM, this indicates the pumps are air locked, perform a vacuum fill, Continue to add coolant and purge until the coolant level reaches between the NOM and MAX Lines on the bottle.
-
Install RH rear HV battery interior bolt.
Note1x bolt, 16mm, 66 Nm, Lift up carpet for access.
-
Install LH rear HV battery interior bolt.
Note1x bolt, 16mm, 66 Nm, Lift up carpet for access.
-
Install rear carpet section.
Note2x push clips, Tuck corners under lower C pillar trim.
-
Connect 2nd row seat harness and secure cushion.
Note2x clips, 2x connectors, Insert buckles through holes, Slide rear inward then align front clips, Perform push-pull-push test.
-
Close LH rear door.
NoteRelease latch before closing if manually latched.
-
Close RH rear door.
NoteRelease latch before closing if manually latched.
- Open LH front door.
-
Install LH front footwell HV battery bolts.
Note2x bolts, EP20, 136 Nm.
-
Install LH front main cabin carpet to vehicle.
Note2x push clips, Number of clips on new vehicles may vary.
-
Install LH console side panel carpet.
Note11x clips, 2x positioning clips, 1x tab, Position side panel and align the front tab, Push the console panel from the front towards the rear.
-
Install connectors to LH footwell cover .
Note1x connector, 1x OBDII connector, Ensure tabs engage on OBDII connector.
-
Install LH footwell cover.
Note2x magnets,1x guide tab.
-
Install LH lower A-pillar assembly.
Note4x clips, 2x guide tabs, Align the 2 front tabs then align the slot with harness bracket and then push rear clip to secure to lower B-pillar, Fully seat seal along trim.
-
Install clip securing LH lower A-pillar assembly.
Note1x push clip.
-
Install LH IP end cap.
Note5x clips, 2x guide tabs.
-
Install LH front primary seal.
NoteVerify seal is seated properly on all trim panels.
-
Install LH front floor mat.
-
Open RH front door.
-
Install RH front footwell HV battery bolts.
Note2x bolts, EP20, 136 Nm.
-
Unfold RH front main cabin carpet back to original position.
Note1x clip.
-
Install RH console side panel carpet.
Note12x clips, 2x positioning clips, 1x datum, Position side panel and align the front datum, Push the console panel from the front towards the rear.
-
Install RH footwell cover .
Note2x magnets, 1x guide tab, 1x connector.
-
Install RH lower A-pillar trim.
Note4x clips, 2x guide tabs, Align the 2 front tabs then align the slot with harness bracket and then push rear clip to secure to lower B-pillar, Fully seat seal along trim.
-
Install clip for RH lower A-pillar trim.
Note1x push clip.
-
Install RH IP end cap.
Note5x clips, 2x guide tabs.
-
lnstall seat lower section of RH front primary seal.
NoteVerify seal is seated properly on all trim panels.
-
Install RH front floor mat.
-
Close RH front door.
-
Inspect coolant level and top off as necessary.
NoteEnsure that fluid level is at Max line.
-
Install coolant bottle cap.
-
Install frunk assembly to vehicle.
Note4x clips, Replace any clips if broken or missing.
-
Install bolts securing frunk assembly.
Note6x bolts, 10mm, 5 Nm.
-
Install frunk service panel.
Note3x clips, Push towards rear of vehicle to secure.
-
Install access panel to frunk assembly.
Note3x clips, 1x connector, Frunk safety switch, 3x guide tabs, Align 3x tabs then push forward to secure clips.
-
Install fresh air gutter assembly.
Note3x clips.
-
Install rear underhood apron.
Note14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips.
- Close hood.
-
Install LH rocker panel lower cover into position.
Note10x clips.
-
Install bolts securing LH rocker panel lower cover to body.
Note4x bolts, 10mm, 5 Nm, Secure 4x covers, The number of fasteners on newer vehicles may vary.
-
Install clips securing the LH rocker panel lower cover to wheel liners.
Note4x push clips.
-
Install RH rocker panel lower cover into position.
Note10x clips.
-
Install bolts securing RH rocker panel lower cover to body.
Note4x bolts, 10mm, 5 Nm, Secure 4x covers, The number of fasteners on newer vehicles may vary.
-
Install clips securing the RH rocker panel lower cover to wheel liners.
Note4x push clips.
-
Exit Service Mode through UI.
NoteExit Service Mode: Controls > Service Mode > Exit Service Mode, Press and hold to exit.
-
Raise all windows.
- Close LH front door.