25/12/2023 01:56:22

Switch - Steering Wheel - LH (Remove and Replace)

Correction code 3205010042 FRT 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2023-12-25: Added Software Reinstall and updated connector image.

Torque Specifications

Table 1. Torque Specifications: Switch - Steering Wheel - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Screw that attaches the LH steering wheel switch to the steering wheel
1 Nm (.7 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • Torx T8 bit
Reuse
Screws (x3) that attach the LH steering wheel switch to the steering wheel
1.2 Nm (.9 lbs-ft)
  • Cordless 1/4in Dr Ratchet
  • Torx T10 socket
  • 2 in extension
Reuse

Remove

  1. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  2. Disconnect the LV power. See LV Battery - Li-lon (Disconnect and Connect).
  3. Remove the driver airbag. See Airbag - Driver (Remove and Replace).
  4. Remove the steering wheel. See Steering Wheel (Remove and Replace).
  5. Remove the steering wheel lower spoker cover. See Cover - Lower Spoke - Steering Wheel (Remove and Replace).
  6. Release the harness from the LH steering wheel switch harness bracket.
  7. Remove the screw that attaches the LH steering wheel switch to the steering wheel.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • Torx T8 bit
  8. Remove the LH steering wheel heater connector from the LH switch harness bracket.
  9. Remove the screws (x3) that attach the LH steering wheel switch to the steering wheel.
    Tip: Use of the following tool(s) is recommended:
    • Cordless 1/4in Dr Ratchet
    • Torx T10 socket
    • 2 in extension
  10. Remove the LH switch fixing bracket from the steering wheel.
  11. Disconnect the LH steering wheel switch connector, and then remove the LH steering wheel switch from the steering wheel.

Install

  1. Install the LH steering wheel switch to the steering wheel, and then connect the LH steering wheel switch connector.
  2. Install the screw that attaches the LH steering wheel switch to the steering wheel.
    1 Nm (.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • Torx T8 bit
  3. Install the LH switch fixing bracket to the steering wheel.
  4. Install the screws (x3) that attach the LH steering wheel switch to the steering wheel.
    1.2 Nm (.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless 1/4in Dr Ratchet
    • Torx T10 socket
    • 2 in extension
  5. Install the LH steering wheel heater connector to the LH switch harness bracket.
  6. Secure the harness to the LH steering wheel switch harness bracket.
  7. Install the steering wheel lower spoker cover. See Cover - Lower Spoke - Steering Wheel (Remove and Replace).
  8. Install the steering wheel. See Steering Wheel (Remove and Replace).
  9. Install the driver airbag. See Airbag - Driver (Remove and Replace).
  10. Connect the LV power. See LV Battery - Li-lon (Disconnect and Connect).
  11. Enter Service Mode. See Service Mode.
  12. Reinstall software. See Software Reinstall - Touchscreen.
  13. Exit Service Mode. See Service Mode.
  14. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).