Blower Motor - HVAC (Remove and Replace)

Correction code 1810010022 FRT 2.34 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Blower Motor - HVAC (Remove and Replace)

Description	Torque Value	Recommended Tools	Reuse/Replace	Notes
Bolts (x3) that attach the HVAC blower motor to the HVAC module	1.2 Nm (.9 lbs-ft)	6 mm socket Ratchet/torque wrench	Reuse
Bolt that attaches the HVAC module to the body	5.5 Nm (4.1 lbs-ft)	Cordless Ratchet/Impact Driver 10 mm deep socket 3 in extension Ratchet/torque wrench	Reuse
Bolts (x2) that attach the RH corners of the cross car beam to the body	29 Nm (21.4 lbs-ft)	Cordless Ratchet/Impact Driver 15 mm socket 3 in extension Ratchet/torque wrench	Reuse
Bolts (x2) that attach the LH corners of the cross car beam to the body	29 Nm (21.4 lbs-ft)	Cordless Ratchet/Impact Driver 15 mm socket 3 in extension Ratchet/torque wrench	Reuse
Bolts (x4) that attach the cross car beam to the HVAC assembly	5.5 Nm (4.1 lbs-ft)	Cordless Ratchet/Impact Driver 10 mm socket 3 in extension Ratchet/torque wrench	Reuse
Bolts (x2) that attach the steering column to the body	25 Nm (18.4 lbs-ft)	Cordless Ratchet/Impact Driver 13 mm socket 3 in extension Ratchet/torque wrench Flex head ratchet/flex head torque wrench	Reuse
Bolt that attaches the cross car beam to the upper side of the cowl	25 Nm (18.4 lbs-ft)	13mm 12-point combination wrench Flex head ratchet/flex head torque wrench Ratchet/torque wrench 13 mm socket	Reuse
Bolt that attaches the cross car beam to the HVAC assembly	5.5 Nm (4.1 lbs-ft)	10 mm socket Ratchet/torque wrench	Reuse
Nuts (x4) that attach the steering column to the cross car beam	15 Nm (11.1 lbs-ft)	Cordless Ratchet/Impact Driver 13 mm socket 3 in extension Ratchet/torque wrench Flex head ratchet/flex head torque wrench	Reuse
Bolts (x2) that attach the LH and RH rear of the center console to the body	7 Nm (5.2 lbs-ft)	Cordless Ratchet/Impact Driver 10 mm socket 2 in extension Ratchet/torque wrench	Reuse
Bolts (x2) that attach the LH front of the center console to the body	7 Nm (5.2 lbs-ft)	Cordless Ratchet/Impact Driver 10 mm socket 2 in extension Ratchet/torque wrench	Reuse
Bolts (x2) that attach the RH front of the center console to the body	7 Nm (5.2 lbs-ft)	Cordless Ratchet/Impact Driver 10 mm socket 2 in extension Ratchet/torque wrench	Reuse