2025-10-20

Link - Lateral - Lower - Front - LH (Remove and Replace)

Correction code 3101021022 FRT 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2025-10-20: Clarified throughout document that LH front lower lateral link to front subframe bolt torque value is only 190 Nm in EMEA/APAC. NA still uses 135 Nm.
  • 2025-07-23: Updated the torque of the bolts that attach the LH front lower lateral link to the front subframe to 190 Nm (EMEA/APAC only).
  • 2024-02-23: Updated the information about the bolts (x2) that attach the front lower lateral link to the subframe. The bolts need to be discarded and their torque values are 135 Nm.

Torque Specifications

Table 1. Torque Specifications: Link - Lateral - Lower - Front - LH (Remove and Replace) Link - Lateral - Lower - Front - Pair (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Nut that attach LH front lower lateral link to the knuckle
180 Nm (132.7 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 22 mm socket
  • Ratchet/torque wrench
 Replace 1109263-00-B
Precote 85 Patch Bolts (x2) that attach the LH front lower lateral link to the front subframe
Informational PurposesAn informational icon, calling your attention
Note
This bolt is only available outside of NA. If in NA, use 1109912-00-B and torque to 135 Nm.
190 Nm (140.1 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 21 mm deep socket
  • Ratchet/torque wrench
 Replace 2123635-00-A
Nylon Patch Bolts (x2) that attach the LH front lower lateral link to the front subframe
135 Nm (99.6 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 21 mm deep socket
  • Ratchet/torque wrench
 Replace 1109912-00-B
Bolt and nut that attach the LH strut to the LH front lower lateral link
106 Nm (78.2 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 21 mm deep socket
  • Ratchet/torque wrench
 Reuse

Remove

  1. Inspect the vehicle for abnormal tire wear that might indicate the need for a wheel alignment. Note any findings.
  2. Raise and support the vehicle. See Raise Vehicle - 2 Post Lift.
  3. Remove the LH front wheel. See Wheel Assembly (Remove and Install).
  4. Remove the front aero shield. See Panel - Aero Shield - Front (Remove and Replace).
  5. Remove and discard the nut that attaches the LH front lower lateral link to the knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 22 mm socket
    • Ratchet/torque wrench
  6. Remove and discard the bolts (x2) that attach the LH front lower lateral link to the front subframe.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 21 mm deep socket
    • Ratchet/torque wrench
  7. Remove the bolt and nut that attach the LH strut to the LH front lower lateral link, and then remove the LH front lower lateral link from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 21 mm deep socket
    • Ratchet/torque wrench

Install

  1. Position the LH front lower lateral link into the vehicle, and then hand tighten the bolt and nut that attach the LH strut to the LH front lower lateral link.
  2. Hand-tighten the new bolts (x2) that attach the LH front lower lateral link to the front subframe.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Install only bolt PN 2123635-00-A or newer.
  3. Install a new nut that attaches the LH front lower lateral link to the knuckle.
    180 Nm (132.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 22 mm socket
    • Ratchet/torque wrench
  4. Tighten the bolts (x2) that attach the LH front lower lateral link to the front subframe.
    190 Nm (140.1 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Refer to the torque table for the correct bolt part number and torque values. These vary across regions, and using the incorrect bolt or torque may damage the subframe.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 21 mm deep socket
    • Ratchet/torque wrench
  5. Install the front aero shield. See Panel - Aero Shield - Front (Remove and Replace).
  6. Remove the bolt that attaches the LH front rotor to the LH front hub.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 10 mm socket
    • 2 in extension
  7. Install the hub jack adapter onto the LH front hub and hand-tighten the lug nuts (x5).
  8. Position and raise the underhoist stand to simulate the suspension at ride height.
  9. Measure the distance between the bottom of the fender and the center of the front axle to make sure that the front suspension is set to ride height. The distance should measure 423 mm.
  10. Tighten the bolt and nut that attach the LH strut to the LH front lower lateral link, and then mark the bolt and nut with a paint pen.
    106 Nm (78.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 21 mm deep socket
    • Ratchet/torque wrench
  11. Remove the underhoist stand from underneath the LH front suspension.
  12. Remove the lug nuts (x5) that attach the hub jack adapter, and then remove the hub jack adapter from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Gently tap with a dead blow to aid
  13. Install the bolt that attaches the LH front rotor to the LH front hub.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 10 mm socket
    • 2 in extension
  14. Install the LH front wheel. See Wheel Assembly (Remove and Install).
  15. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust as a separate activity. See Alignment Requirement - Suspension.