01/04/2024 13:57:00

Assembly - Brake Pedal (RHD) (Remove and Replace)

Correction code 3325010112 FRT 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Assembly - Brake Pedal (RHD) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt and the nuts (x4) that attach the brake pedal assembly to the vehicle Nuts
16.5 Nm (12.2 lbs-ft)
Bolt
13 Nm (9.6 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 13 mm deep socket
  • 4 in extension
  • Ratchet/torque wrench

Nut: Replace

Bolts: Reuse

 Nut: 1111541-00-A

Remove

  1. Open the RH front door and lower the RH front window.
  2. Move the driver's seat backward.
  3. Remove the rear apron. See Underhood Apron - Rear (Remove and Replace).
  4. Disconnect the LV battery power. See LV Battery - Li-lon (Disconnect and Connect).
  5. Remove the RH footwell cover. See Cover - Footwell - Driver (RHD) (Remove and Replace).
  6. Remove the brake clevis clip. See Clevis Pin - Brake Pedal (Remove and Replace).
  7. Disconnect the accelerator pedal electrical connector.
  8. Remove the bolt and the nuts (x4) that attach the brake pedal assembly to the vehicle, and then discard the nuts.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 13 mm deep socket
    • 4 in extension
    • Ratchet/torque wrench
  9. Remove the brake pedal and the accelerator pedal as an assembly from the vehicle.

Install

  1. Position the brake pedal assembly onto the body.
  2. Install the bolt and the new nuts (x4) that attach the brake pedal assembly to the vehicle.
    16.5 Nm (12.2 lbs-ft)
    13 Nm (9.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 13 mm deep socket
    • 4 in extension
    • Ratchet/torque wrench
  3. Connect the accelerator pedal electrical connector.
  4. Install the brake clevis clip. See Clevis Pin - Brake Pedal (Remove and Replace).
  5. Install the RH footwell cover. See Cover - Footwell - Driver (RHD) (Remove and Replace).
  6. Connect the LV battery power. See LV Battery - Li-lon (Disconnect and Connect).
  7. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  8. Click the Actions tab, and then type "TEST-SELF_DI_X_ACCEL-PEDAL" into the search field.
  9. Click TEST-SELF_DI_X_ACCEL-PEDALvia Toolbox: (link), click Run, and allow the routine to complete.
  10. Disconnect the laptop with Toolbox 3 from the vehicle. See Toolbox 3 (Connect and Disconnect).
  11. Install the rear apron. See Underhood Apron - Rear (Remove and Replace).
  12. Move the driver seat back to its original position.
  13. Raise the RH front window and close the RH front door.