18/06/2024 00:53:30

Brake Caliper - Front (Sport Brakes) - RH (Remove and Replace)

Correction code 3301010022 FRT 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-06-17: Revised last step to either do a road test or perform brake pad burnishing procedure.

Torque Specifications

Table 1. Torque Specifications: Brake Caliper - Front (Sport Brakes) - LH (Remove and Replace) Brake Caliper - Front (Sport Brakes) - RH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the LH/RH front brake hose bracket to the knuckle
5 Nm (3.7 lbs-ft)
  • Ratchet/torque wrench
  • 4 in extension
  • 10 mm socket
 Reuse
Nut that attaches the LH/RH front brake line to the LH/RH front brake hose
16 Nm (11.8 lbs-ft)
  • ¼ in to 3/8 in adapter
  • Ratchet/torque wrench
  • 12 mm socket
 Reuse
Nut that attaches the LH/RH front brake hose to body
6 Nm (4.4 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 10 mm deep socket
  • Ratchet/torque wrench
 Reuse
Bolt that attaches the LH/RH front brake hose to the LH/RH front brake caliper
42 Nm (31.0 lbs-ft)
  • 11 mm deep socket
  • Ratchet/torque wrench
 Replace Replace the fastener together with the brake hose.
Bolts (x2) that attach the LH/RH front brake caliper to the LH/RH front knuckle
94 Nm (69.3 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 3/8 in to ½ in adapter
  • External Torx E18
  • Breaker bar
  • Ratchet/torque wrench
 Replace 1088969-00-B

Remove

  1. Place the vehicle on the 2-post lift.
    Tip: Ensure the vehicle is not charging.
  2. Open the LH front door and lower the LH front window.
  3. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  4. Remove the RH front wheel. See Wheel Assembly (Remove and Install).
  5. Position an oil drain receiver under the RH front brake hose area.
  6. Release the bolt that attaches the RH front brake hose bracket to the knuckle.
    Tip: Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 4 in extension
    • 10 mm socket
    Figure 1. LH Shown. RH Similar
  7. Remove the nut that attaches the RH front brake line to the RH front brake hose.
    Tip: Use of the following tool(s) is recommended:
    • ¼ in to 3/8 in adapter
    • Ratchet/torque wrench
    • 12 mm socket
    Figure 2. LH Shown. RH Similar
  8. Remove the nut that attaches the RH front brake hose to body.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 10 mm deep socket
    • Ratchet/torque wrench
    Figure 3. LH Shown. RH Similar
  9. Remove and discard the bolt that attaches the RH front brake hose to the RH front brake caliper.
    Tip: Use of the following tool(s) is recommended:
    • 11 mm deep socket
    • Ratchet/torque wrench
  10. Remove and discard the bolts (x2) that attach the RH front brake caliper to the RH front knuckle, and then remove the front brake caliper.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 3/8 in to ½ in adapter
    • External Torx E18
    • Breaker bar
    • Ratchet/torque wrench
    Figure 4. LH Shown. RH Similar

Install

  1. Install new bolts (x2) (1088969-00-B) that attach the RH front brake caliper to the RH front knuckle.
    94 Nm (69.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 3/8 in to ½ in adapter
    • External Torx E18
    • Breaker bar
    • Ratchet/torque wrench
    Figure 5. LH Shown. RH Similar
  2. Install the bolt that attaches the new RH front brake hose to the RH front brake caliper.
    42 Nm (31.0 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 11 mm deep socket
    • Ratchet/torque wrench
  3. Install the nut that attaches the RH front brake hose to body.
    6 Nm (4.4 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 10 mm deep socket
    • Ratchet/torque wrench
    Figure 6. LH Shown. RH Similar
  4. Install the nut that attaches the RH front brake line to the RH front brake hose.
    16 Nm (11.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • ¼ in to 3/8 in adapter
    • Ratchet/torque wrench
    • 12 mm socket
    Figure 7. LH Shown. RH Similar
  5. Install the bolt that attaches the RH front brake hose bracket to the knuckle.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 4 in extension
    • 10 mm socket
    Figure 8. LH Shown. RH Similar
  6. Remove the oil drain receiver from underneath the vehicle.
  7. Bleed the RH front caliper. See Brake Fluid Bleed - One Caliper \(Remove and Replace\).
  8. Install the RH front wheel. See Wheel Assembly (Remove and Install).
  9. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  10. Raise the LH front window and close the LH front door.
  11. Remove the lift arms from below the vehicle.
  12. Perform one of the following:
    • If the brake pads were not replaced in this procedure, perform a road test using a series of aggressive stops and make sure that there is proper brake pedal feel and brake performance.
      Informational PurposesAn informational icon, calling your attention
      Note
      Add test drive correction code 00040100 as a separate activity to the Service Visit.
    • If the brake pads were replaced in this procedure, perform the brake pad burnishing procedure. See Brake Pads - Burnishing.
      Informational PurposesAn informational icon, calling your attention
      Note
      Add the correction code for brake pad burnishing 33013000 as a separate activity to the Service Visit.