17/10/2023 18:49:06

Window Motor / Regulator Assembly - Rear - LH (Remove and Replace)

Correction code 1150010062 FRT 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Window Motor / Regulator Assembly - Rear - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Screws (x12) that attach the LH rear window motor/regulator assembly to the LH rear door
4 Nm (2.9 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 8 mm socket
  • 2 in extension
  • Ratchet/torque wrench
Reuse

Remove

  1. Open the LH front door and lower the LH front window.
  2. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  3. Remove the LH rear door puddle light. See Puddle Lamp - Rear Door (Remove and Replace).
  4. Remove the LH rear door trim panel. See Panel - Door Trim - Rear - LH (Remove and Replace).
  5. Remove the LH rear door glass. See Glass - Door - Rear - LH (Remove and Replace).
  6. Disconnect LV power. See LV Battery - Li-lon (Disconnect and Connect).
  7. Disconnect the electrical harness from the LH rear window motor/regulator assembly.
  8. Disconnect the electrical harness from the LH rear door pressure sensor.
  9. Release the clips (x2) that attach the LH rear door harness to the LH rear window motor/regulator assembly.
  10. Release the clip that attaches the manual latch release cable to the LH rear window motor/regulator assembly.
  11. Remove the screws (x12) and release the metal clips (x2) that attach the LH rear window motor/regulator assembly to the LH rear door, and then remove the assembly from the door.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Never loosen or remove the nuts (x4) that attach the regulator arms to the assembly closeout panel.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 8 mm socket
    • 2 in extension
    • Ratchet/torque wrench

Install

  1. Inspect the condition of the mounting holes for the LH rear window motor/regulator assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Install rivnuts where any of the mounting hole threads are stripped. Use a 7.5mm drill to prepare the hole for rivnut installation.
  2. Install the LH rear window motor/regulator assembly to the LH rear door, hand-install the screws (x12) and fasten the metal clips that attach the assembly to the door, and then tighten the screws.
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 8 mm socket
    • 2 in extension
    • Ratchet/torque wrench
  3. Fasten the clips (x2) that attach the LH rear door harness to the LH rear window motor/regulator assembly.
  4. Connect the electrical harness to the LH rear window motor/regulator assembly.
  5. Connect the electrical harness to the LH rear door pressure sensor.
  6. Fasten the clip that attaches the manual latch release cable to the LH rear window motor/regulator assembly.
  7. Connect LV power. See LV Battery - Li-lon (Disconnect and Connect).
  8. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  9. Install the LH rear door glass. See Glass - Door - Front - LH (Remove and Replace).
  10. Install the LH rear door puddle light. See Puddle Lamp - Rear Door (Remove and Replace).
  11. Install the LH rear door trim panel. See Panel - Door Trim - Rear - LH (Remove and Replace).
  12. Calibrate the LH rear window regulator. See Window Regulator (Recalibrate) (Module Reset/Reflashed).
  13. Raise the LH front window and close the LH front door.