17/04/2024 00:02:29

Bracket - Fascia Side to Fender - LH (Remove and Replace)

Correction code 1001020062 FRT 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-04-17: Updated the front fascia LH corner bolt torque from 4 Nm to 2.5 Nm.

Torque Specifications

Table 1. Torque Specifications: Bracket - Fascia Side to Fender - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the front fascia to the LH front fender
2.5 Nm (1.8 lbs-ft)
  • Cordless hex driver
  • 8 mm magnetic deep
  • 6 in nutsetter
Reuse
Nuts (x2) that attach the LH fascia side to fender bracket to the LH front fender
4 Nm (2.9 lbs-ft)
  • 10 mm socket
  • Cordless Ratchet/Impact Driver
  • Ratchet/torque wrench
Reuse

Remove

  1. Open the LH front door and lower the LH front window.
  2. Press the brake pedal to turn on the drive rail.
  3. Turn the steering wheel all the way to the right.
  4. Remove the clips (x3) that attach the LH front wheel arch liner to the front fascia, and then move the liner aside for access.
  5. Remove the bolt that attaches the front fascia to the LH front fender.
    Tip: Use of the following tool(s) is recommended:
    • Cordless hex driver
    • 8 mm magnetic deep
    • 6 in nutsetter
  6. Use a plastic trim tool to release the clips (x6) that attach the front fascia to the front fender.
  7. Carefully pull aside the corner of the front fascia away from the front fender.
  8. Remove the nuts (x2) that attach the LH fascia side to fender bracket to the LH front fender, and then remove the bracket from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench

Install

  1. Position the LH fascia side to fender bracket onto the LH front fender.
  2. Install the nuts (x2) that attach the LH fascia side to fender bracket to the LH front fender.
    4 Nm (2.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  3. Install the clips (x6) that attach the front fascia to the front fender.
  4. Install the bolt that attaches the front fascia to the LH front fender.
    2.5 Nm (1.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless hex driver
    • 8 mm magnetic deep
    • 6 in nutsetter
  5. Install the clips (x3) that attach the LH front wheel arch liner to the front fascia.
  6. Press the brake pedal to turn on the drive rail.
  7. Set the steering wheel straight ahead.
  8. Raise the LH front window and raise the LH front door.