17/10/2023 18:55:25

Pretensioner - Driver (Remove and Replace)

Correction code 2010010022 FRT 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Pretensioner - Driver (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the pretensioner to the seat track
40 Nm (29.5 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • Internal Torx Plus IP50 socket
  • Flex head ratchet/flex head torque wrench (for installation only)
 Replace

Remove

  1. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  2. Remove the LH side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  3. Remove the 2nd row lower seat cushion. See Seat Cushion - 2nd Row (Remove and Replace).
  4. Remove the end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  5. Remove the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  6. Remove the LH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Remove and Replace).
  7. Release the seatbelt retractor from the driver seat.
  8. Move the driver seat cushion all way up.
    Informational PurposesAn informational icon, calling your attention
    Note
    Adjust the seat back if necessary to avoid contact with the headliner.
  9. Disconnect the LV battery. See LV Battery - Li-lon (Disconnect and Connect).
  10. Remove the driver seat outboard side shield. See Side Shield - Outboard - LH (Remove and Replace).
  11. Disconnect the electrical connector from the pretensioner.
  12. Remove and discard the bolt that attaches the pretensioner to the seat track.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • Internal Torx Plus IP50 socket
    • Flex head ratchet/flex head torque wrench (for installation only)
  13. Remove the 1st row outboard lap pretensioner from the seat track.

Install

  1. Install the bolt that attaches the pretensioner to the seat track.
    40 Nm (29.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • Internal Torx Plus IP50 socket
    • Flex head ratchet/flex head torque wrench (for installation only)
  2. Connect the electrical connector to the pretensioner.
  3. Install the driver seat outboard side shield. See Side Shield - Outboard - LH (Remove and Replace).
  4. Connect the LV battery. See LV Battery - Li-lon (Disconnect and Connect).
  5. Install the seatbelt retractor to the driver seat.
  6. Install the LH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Remove and Replace).
  7. Install the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  8. Install the end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  9. Install the 2nd row lower seat cushion. See Seat Cushion - 2nd Row (Remove and Replace).
  10. Install the LH side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  11. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).