2025-10-23

Phone Dock (Clip) - Center Console (Remove and Replace)

Correction code 1519010222 FRT 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Informational PurposesAn informational icon, calling your attention
Note
There are 2 types of phone docks on the 2024+ Model 3: a clip-secured type on vehicles built before March 3rd, 2024, and a screw-secured type on vehicles built on or after March 3rd, 2024.
Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
To avoid damage, do not perform this procedure on a vehicle built on or after March 3rd, 2024 or if the vehicle build date is unknown. Refer to Phone Dock (Screw) - Center Console (Remove and Replace).

Torque Specifications

Table 1. Torque Specifications: Phone Dock (Clip) - Center Console (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Screws (x3) that attach the inductive charger to the phone dock
1 Nm (.7 lbs-ft)
  • Torx T20 socket
 Reuse

Remove

  1. Open the LH front door and lower the LH front window.
  2. Release the clips (x4) and tabs (x6) that attach the phone dock to the center console.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the bottom of the phone dock rearward along the center console.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not use excessive force. If the phone dock will not release, refer to Phone Dock (Screw) - Center Console (Remove and Replace).
  3. Disconnect the electrical connector, and then remove the phone dock from the instrument panel.
  4. Remove the screws (x3) that attach the inductive charger to the phone dock.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
  5. Release the tabs (x2) and datums (x2) that attach the inductive charger to the phone dock, and then remove the inductive charger from the phone dock.
    Informational PurposesAn informational icon, calling your attention
    Note
    Angle the inductive charger up and slide out of the phone dock.

Install

  1. Fasten the tabs (x2) and datums (x2) that attach the inductive charger into the phone dock.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the inductive charger datums into the phone dock, and then fully engage the tabs at the top of the phone dock.
  2. Install the screws (x3) that attach the inductive charger to the phone dock.
    1 Nm (.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 socket
  3. Connect the electrical connector, and then install the phone dock to the instrument panel.
  4. Fasten the clips (x4) and tabs (x6) that attach the phone dock to the center console.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the datums forward into the center console, and then secure the tabs down.
  5. Raise the LH front window and close the LH front door.