25/08/2024 19:57:15

Blower - Cushion - Front Seat - LH (Remove and Replace)

Correction code 1301010312 FRT 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Seat base edges are sharp and can cause personal injury. Wear cut resistant gloves when removing the seat from the vehicle, and while performing procedures that involve work on or near the seat base.

Torque Specifications

Table 1. Torque Specifications: Blower - Cushion - Front Seat - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) that attach the rear of the driver seat to the body
33.5 Nm (24.7 lbs-ft)
  • Torx Plus T45 socket
  • Cordless Ratchet/Impact Driver
  • Flex head ratchet/flex head torque wrench
 Replace
Bolts (x2) that attach the front of the driver seat to the body
33.5 Nm (24.7 lbs-ft)
  • Torx Plus T45 socket
  • Cordless Ratchet/Impact Driver
  • Flex head ratchet/flex head torque wrench
 Replace

Remove

  1. Open the LH front door and lower the LH front window.
  2. Move the driver seat fully forward.
  3. Remove and discard the bolts (x2) that attach the rear of the driver seat to the body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use only the Torx Plus T45 bit to remove the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • Cordless Ratchet/Impact Driver
    • Flex head ratchet/flex head torque wrench
  4. Move the driver seat fully rearward.
  5. Remove and discard the bolts (x2) that attach the front of the driver seat to the body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use only the Torx Plus T45 bit to remove the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • Cordless Ratchet/Impact Driver
    • Flex head ratchet/flex head torque wrench
  6. Tilt the driver seat rearward to gain access to the driver seat cushion ventilation fan.
  7. Disconnect the electrical connector from the driver seat cushion ventilation fan.
  8. Release the clips (x2) and guide tab that attach the driver seat cushion ventilation fan to the driver seat frame, and then remove the fan from the vehicle.

Install

  1. Fasten the clips (x2) and guide tab that attach the driver seat cushion ventilation fan to the driver seat frame.
  2. Connect the electrical connector to the driver seat cushion ventilation fan.
  3. Tilt the driver seat forward back to its original position.
  4. Install new bolts (x2) that attach the front of the driver seat to the body.
    33.5 Nm (24.7 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use only the Torx Plus T45 bit to remove the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • Cordless Ratchet/Impact Driver
    • Flex head ratchet/flex head torque wrench
  5. Move the driver seat fully forward.
  6. Install new bolts (x2) that attach the rear of the driver seat to the body.
    33.5 Nm (24.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Torx Plus T45 socket
    • Cordless Ratchet/Impact Driver
    • Flex head ratchet/flex head torque wrench
  7. Move the driver seat back to its original position.
  8. Raise the LH front window and close the LH front door.