18/10/2023 18:16:12

Bracket Assembly - A/C Compressor (Remove and Replace)

Correction code 1820020032 FRT 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Bracket Assembly - A/C Compressor (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the ground strap to the A/C compressor
7 Nm (5.2 lbs-ft)
  • Torx T25 socket
  • Cordless Ratchet/Impact Driver
  • Ratchet/torque wrench (for installation only)
 Reuse
Bolts (x2) that attach the A/C compressor assembly to the brace
31 Nm (22.9 lbs-ft)
  • 15 mm socket
  • Cordless Ratchet/Impact Driver
  • Ratchet/torque wrench (for installation only)
 Reuse
Bolts (x3) that attach the bracket to the compressor
9 Nm (6.6 lbs-ft)
  • 10 mm deep socket
  • Cordless Ratchet/Impact Driver
  • Ratchet/torque wrench (for installation only)
 Reuse

Remove

  1. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  2. Disconnect LV power. See LV Battery - Li-lon (Disconnect and Connect).
  3. Remove LV power. See LV Battery (Remove and Replace).
  4. Release the connector locking tab, then disconnect the A/C logic electrical connector from the A/C compressor.
    Informational PurposesAn informational icon, calling your attention
    Note
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
    Tip: Use of the following tool(s) is recommended:
    • Pick Miniature Soft Grip, 90 degree tip, 6 in
  5. Use a clip prytool to release the retaining clip that attaches the A/C compressor logic harness to the A/C compressor HV harness bracket.
  6. Remove the bolt that attaches the ground strap to the A/C compressor, and then set the ground strap aside.
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench (for installation only)
  7. Use a clip pry tool to release the clip that attaches the coolant hose to the A/C compressor bracket.
  8. Use a clip pry tool to release the clips (x2) that attach the coolant hose to the A/C compressor bracket.
  9. Use a clip pry tool to release the retaining clips (x4) that attach the A/C compressor HV harness to the shock tower support brace.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull upward on the clip to assist with removal. Do not pull upward on the HV cable.
  10. Release the connector locking tab, and then disconnect the HVIL connector near the LH front strut tower.
    Informational PurposesAn informational icon, calling your attention
    Note
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
    Tip: Use of the following tool(s) is recommended:
    • Pick Miniature Soft Grip, 90 degree tip, 6 in
  11. With an assistant, remove the bolts (x2) that attach the A/C compressor assembly to the strut tower brace, and then carefully maneuver the assembly towards the front of the vehicle, under the strut tower support brace. Rest the A/C compressor assembly on the front underhood storage unit reinforcement beam.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not rest the A/C compressor on the HV connector.
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench (for installation only)
  12. With an assistant, remove the bolts (x3) that attach the A/C compressor bracket to the A/C compressor, and then remove the bracket from the compressor.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench (for installation only)

Install

  1. Position the A/C compressor bracket on the A/C compressor, and then install the bolts (x3) that attach the bracket to the compressor.
    9 Nm (6.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    Tip: Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench (for installation only)
  2. With an assistant supporting the A/C compressor assembly under the strut tower brace, hand-start the bolts (x2) that attach the A/C compressor assembly to the brace, and then torque the bolts.
    31 Nm (22.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 15 mm socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench (for installation only)
  3. Install the clips (x2) that attach the coolant hose to the A/C compressor bracket.
  4. Install the clip that attaches the coolant hose to the A/C compressor bracket.
  5. Position the ground strap on the A/C compressor, and then install the bolt that attaches the ground strap to the A/C compressor.
    7 Nm (5.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench (for installation only)
  6. Install the retaining clip that attaches the A/C compressor logic harness to the A/C compressor HV harness bracket.
  7. Connect the A/C compressor logic electrical connector to the A/C compressor, and then engage the locking tab.
    Informational PurposesAn informational icon, calling your attention
    Note
    Push the red locking tab into the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  8. Connect the HVIL connector near the LH front strut tower, and then engage the locking tab.
    Informational PurposesAn informational icon, calling your attention
    Note
    Push the red locking tab into the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  9. Install the retaining clips (x4) that attach the A/C compressor HV harness to the shock tower support brace.
  10. Install LV power. See LV Battery (Remove and Replace).
  11. Connect LV power. See LV Battery - Li-lon (Disconnect and Connect).
  12. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).