08/11/2023 21:22:02

Actuator - Pedestrian Protection - Active Hood - LH (Remove and Replace)

Correction code 2020010052 FRT 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Actuator - Pedestrian Protection - Active Hood - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the strut bracket to the wheel arch, from inside the wheel arch
5 Nm (3.7 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 10 mm deep socket
  • Ratchet/torque wrench
 Reuse
Nuts (x2) that attach the pyrotechnic actuator to the body
6 Nm (4.4 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • Torx T30 socket
  • ¼ in hex to ¼ in square 6 in adapter
  • Ratchet/torque wrench
 Reuse

Remove

  1. Raise and support the vehicle. See GUID-0ECF2493-88F6-48E9-ADBB-9AE1D52E217C.html.
  2. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  3. Disconnect the LV battery. See LV Battery - Li-lon (Disconnect and Connect).
  4. Remove the cabin intake duct. See Assembly - Fresh Air Gutter - HVAC (Remove and Replace).
  5. Remove the access panel. See Cover - Hood Latch (Remove and Replace).
  6. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  7. Remove the LH front wheel. See Wheel Assembly (Remove and Install).
  8. Remove the bolt that attaches the LH front wheel arch liner to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 10 mm deep socket
    • Ratchet/torque wrench
  9. Remove the clips (x8) that attach the LH front wheel arch liner to the body and then partially remove the LH front wheel arch liner.
  10. Disconnect the pyrotechnic actuator connector.
  11. Use a small flat head screwdriver to release the clip that attaches the LH hood strut to the LH hood strut bracket, and then remove the strut from the bracket.
  12. Remove the nuts (x2) that attach the pyrotechnic actuator to the body, and then remove the actuator from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • Torx T30 socket
    • ¼ in hex to ¼ in square 6 in adapter
    • Ratchet/torque wrench

Install

  1. Install the pyrotechnic actuator to the body, and then install the nuts (x2) attach the actuator to the body.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • Torx T30 socket
    • ¼ in hex to ¼ in square 6 in adapter
    • Ratchet/torque wrench
  2. Position the strut to the LH active hood strut bracket, and then install the clip that attaches the strut to the bracket.
  3. Connect the pyrotechnic actuator connector.
  4. Install the clips (x8) that attach the LH front wheel arch liner to the body and then partially remove the LH front wheel arch liner.
  5. Install the bolt that attaches the LH front wheel arch liner to the vehicle.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 10 mm deep socket
    • Ratchet/torque wrench
  6. Install the LH front wheel. See Wheel Assembly (Remove and Install).
  7. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  8. Install the access panel. See Cover - Hood Latch (Remove and Replace).
  9. Connect the LV battery. See LV Battery - Li-lon (Disconnect and Connect).
  10. Install the cabin intake duct. See Assembly - Fresh Air Gutter - HVAC (Remove and Replace).
  11. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  12. Lower the vehicle. See GUID-0ECF2493-88F6-48E9-ADBB-9AE1D52E217C.html.