01/12/2023 09:26:39

Glove Box (RHD) (Remove and Replace)

Correction code 1405010202 FRT 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Table 1. Torque Specifications: Glove Box (RHD) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Screws (x4) that attach the glove box to the instrument panel carrier
2.3 Nm (1.7 lbs-ft)
  • Torx T20 socket
  • 2 in extension
  • Cordless Ratchet/Impact Driver
  • WIHA Torque Screwdriver 0.8-5Nm
  • Mini Ratchet Bit Set - 1450424-00-A
 Reuse
Bolts (x2) that attach the glove box USB cable to the glove box
1.5 Nm (1.1 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 2 in extension
  • Torx T20 socket
  • Ratchet/torque wrench
 Reuse

Remove

  1. Remove the passenger footwell cover. See Cover - Footwell - Front Passenger (RHD) (Remove and Replace).
  2. Remove the LH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  3. Remove the clip that secures the passenger footwell duct.
  4. Release the locking tab, and then disconnect the connector that attaches the glove box USB cable to the car computer.
  5. Remove the screws (x4) that attach the glove box to the instrument panel carrier.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • 2 in extension
    • Cordless Ratchet/Impact Driver
    • WIHA Torque Screwdriver 0.8-5Nm
    • Mini Ratchet Bit Set - 1450424-00-A
  6. Release the clips (x10), the locator pins (x3), and a datum that attach the glove box to the instrument panel carrier.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Avoid damage to the electromagnetic switch.
  7. Disconnect the glove box assembly electrical connectors (x2).
  8. Remove the glove box from the vehicle.
  9. Remove the bolts (x2) that attach the glove box USB cable to the glove box.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 2 in extension
    • Torx T20 socket
    • Ratchet/torque wrench

Install

  1. Install the bolts (x2) that attach the glove box USB cable to the glove box.
    1.5 Nm (1.1 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 2 in extension
    • Torx T20 socket
    • Ratchet/torque wrench
  2. Connect the glove box assembly electrical connectors (x2).
  3. Secure the clips (x10), the locator pins (x3), and a datum that attach the glove box to the instrument panel carrier.
  4. Install the screws (x4) that attach the glove box to the instrument panel carrier.
    2.3 Nm (1.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • 2 in extension
    • Cordless Ratchet/Impact Driver
    • WIHA Torque Screwdriver 0.8-5Nm
    • Mini Ratchet Bit Set - 1450424-00-A
  5. Connect the connector that attaches the glove box USB cable to the car computer, and engage the locking tab.
  6. Install the clip that secures the passenger footwell duct.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure that the footwell duct is installed in proper place.
  7. Install the LH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  8. Install the passenger footwell cover. See Cover - Footwell - Front Passenger (RHD) (Remove and Replace).