18/10/2023 23:40:05

Armrest - Outer - Center Console (Remove and Replace)

Correction code 1519010192 FRT 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Armrest - Outer - Center Console (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Screws (x4) that attach the center console outer armrest to the armrest hinge
1 Nm (.7 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • Torx T20 socket
  • 2 in extension
  • Ratchet/torque wrench
 Reuse

Remove

  1. Remove the center console phone dock. See Phone Dock (Clip) - Interior Trim - Center Console (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    It is not necessary to remove the inductive charger.
  2. Remove the center console end panel. See Panel - Rear End - Center Console (Remove and Replace).
  3. Remove the LH center console rear side panel. See Panel - Rear Side - Center Console - LH (Remove and Replace).
  4. Remove the LH center console front side panel. See Carpet - Side - Center Console - LH (Remove and Replace).
  5. Remove the LH center console décor trim. See Decor Trim - Center Console - LH (Remove and Replace).
  6. Repeat step 3 through step 5 for the RH side of the vehicle.
  7. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  8. Disconnect LV battery power. See LV Battery - Li-lon (Disconnect and Connect)
  9. Remove the rear end module assembly. See Module - Rear End - Center Console (Remove and Replace)
    Informational PurposesAn informational icon, calling your attention
    Note
    No need to remove the rear end module from the assembly.
  10. Remove the armrest assembly. See Armrest - Center Console (Remove and Install) .
  11. Remove the center console inner armrest. See Armrest - Inner - Center Console (Remove and Replace).
  12. Remove the screws (x4) that attach the center console outer armrest to the armrest hinge, and then remove the outer armrest from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • Torx T20 socket
    • 2 in extension
    • Ratchet/torque wrench

Install

  1. Install the screws (x4) that attach the center console outer armrest to the armrest hinge.
    1 Nm (.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • Torx T20 socket
    • 2 in extension
    • Ratchet/torque wrench
  2. Install the center console inner armrest. See Armrest - Inner - Center Console (Remove and Replace).
  3. Install the center console armrest assembly. See Armrest - Center Console (Remove and Install).
  4. Install the rear end module assembly. See Module - Rear End - Center Console (Remove and Replace)
  5. Connect LV battery power. See LV Battery - Li-lon (Disconnect and Connect)
  6. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  7. Install the LH center console décor trim. See Decor Trim - Center Console - LH (Remove and Replace).
  8. Install the LH center console front side panel. See Carpet - Side - Center Console - LH (Remove and Replace).
  9. Install the LH center console rear side panel. See Panel - Rear Side - Center Console - LH (Remove and Replace).
  10. Repeat step 7 through step 9 for the RH side of the vehicle.
  11. Install the center console end panel. See Panel - Rear End - Center Console (Remove and Replace).
  12. Install the center console phone dock. See Phone Dock (Clip) - Interior Trim - Center Console (Remove and Replace).