2025-01-14

Assembly - Brake Pedal (LHD) (Remove and Replace)

Correction code 3325010022 FRT 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-01-15: Added notes to help remove/install the pedal assembly from/to the iBooster studs.
  • 2024-01-04: Updated the routine.

Torque Specifications

Table 1. Torque Specifications: Assembly - Brake Pedal (LHD) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt and the nuts (x4) that attach the brake pedal assembly to the vehicle Nuts
16.5 Nm (12.2 lbs-ft)
Bolt
13 Nm (9.6 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 13 mm deep socket
  • 4 in extension
  • Ratchet/torque wrench

Nut: Replace

Bolts: Reuse

Nut: 1111541-00-A

Remove

  1. Open the LH front door and lower the LH front window.
  2. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  3. Disconnect LV power. See LV Battery - Li-lon (Disconnect and Connect).
  4. Remove the driver footwell cover. See Cover - Footwell - Driver (Remove and Replace).
  5. Remove the LH footwell duct. See Duct - Footwell - LH (Remove and Replace).
  6. Remove the brake clevis clip. See Clevis Pin - Brake Pedal (Remove and Replace).
  7. Disconnect the accelerator pedal electrical connector.
  8. Release the clips (x2) that attach the electrical harness to the brake pedal assembly.
  9. Remove the bolt and the nuts (x4) that attach the brake pedal assembly to the vehicle, and then discard the nuts.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 13 mm deep socket
    • 4 in extension
    • Ratchet/torque wrench
  10. Remove the brake pedal and the accelerator pedal as an assembly from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the brake pedal assembly from the iBooster studs. It is recommended to slightly push the studs or the rod outward to release extra space for the pedal assembly removal. If needed, have an assistant pull the iBooster outside to keep good clearance for taking the pedal assembly off from the studs.

Install

  1. Install the brake pedal assembly onto the studs (x4) of the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    It is recommended to push the studs or the rod outward to release extra space for securing the fasteners. If needed, have an assistant pull the iBooster outside to keep good clearance for installation.
  2. Install the bolt and the new nuts (x4) that attach the brake pedal assembly to the vehicle.
    16.5 Nm (12.2 lbs-ft)
    Nuts
    13 Nm (9.6 lbs-ft)
    Bolt
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 13 mm deep socket
    • 4 in extension
    • Ratchet/torque wrench
  3. Fasten the clips (x2) that attach the electrical harness to the brake pedal assembly.
  4. Connect the accelerator pedal electrical connector.
  5. Install the brake clevis clip. See Clevis Pin - Brake Pedal (Remove and Replace).
  6. Install the LH footwell duct. See Duct - Footwell - LH (Remove and Replace).
  7. Install the driver footwell cover. See Cover - Footwell - Driver (Remove and Replace).
  8. Connect LV power. See LV Battery - Li-lon (Disconnect and Connect).
  9. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  10. Click the Actions tab, and then type "TEST-SELF_DI_X_ACCEL-PEDAL" into the search field, click TEST-SELF_DI_X_ACCEL-PEDALvia Toolbox: (link), click Run, and allow the routine to complete.
  11. Disconnect the laptop with Toolbox 3 from the vehicle. See Toolbox 3 (Connect and Disconnect).
  12. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  13. Raise the LH front window and close the LH front door.