23/02/2024 00:25:09

Link - Lateral - Lower - Front - Pair (Remove and Replace)

Correction code 3101022022 FRT 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-02-23: Updated the information about the bolts that attach the LH and RH front lower lateral link to the subframe. The bolts need to be replaced and their torque values are 135 Nm.

Torque Specifications

Table 1. Torque Specifications: Link - Lateral - Lower - Front - Pair (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Nuts that attach the LH and RH front lower compliance link to the knuckle
180 Nm (132.7 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 22 mm deep socket
  • Ratchet/torque wrench
 Replace 1109263-00-B
Bolts that attach the LH and RH front lower lateral link to the front subframe
135 Nm (99.6 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 21 mm deep socket
  • Ratchet/torque wrench
 Replace Install only bolt PN 1109912-00-B (China 1109912-99-B) or newer, which has patch material on the bolt threads.
Bolt and nut that attach the LH and RH strut to the LH front lower lateral link
106 Nm (78.2 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 21 mm deep socket
  • Ratchet/torque wrench
 Reuse

Remove

  1. Inspect the vehicle for abnormal tire wear that might indicate the need for a wheel alignment. Note any findings.
  2. Raise and support the vehicle. See GUID-0ECF2493-88F6-48E9-ADBB-9AE1D52E217C.html.
  3. Remove the front wheels. See Wheel Assembly (Remove and Install).
  4. Remove the front aero shield. See Panel - Aero Shield - Front (Remove and Replace).
  5. Remove and discard the nut that attaches the LH front lower lateral link to the knuckle.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 22 mm socket
    • Ratchet/torque wrench
  6. Remove and discard the bolts (x2) that attach the LH front lower lateral link to the front subframe.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 21 mm deep socket
    • Ratchet/torque wrench
  7. Remove the bolt and nut that attach the LH strut to the LH front lower lateral link, and then remove the LH front lower lateral link from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 21 mm deep socket
    • Ratchet/torque wrench
  8. Repeat step 5 through step 7 for the RH side of the vehicle.

Install

  1. Position the LH front lower lateral link into the vehicle, and then hand tighten the bolt and nut that attach the LH strut to the LH front lower lateral link.
  2. Hand-tighten the new bolts (x2) that attach the LH front lower lateral link to the front subframe.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Install only bolt PN 1109912-00-B (China 1109912-99-B) or newer, which has patch material on the bolt threads.
  3. Install a new nut that attaches the LH front lower lateral link to the knuckle.
    180 Nm (132.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 22 mm socket
    • Ratchet/torque wrench
  4. Tighten the bolts (x2) that attach the LH front lower lateral link to the front subframe.
    135 Nm (99.6 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 21 mm deep socket
    • Ratchet/torque wrench
  5. Repeat 1 through step 4 for the RH side of the vehicle.
  6. Install the front aero shield. See Panel - Aero Shield - Front (Remove and Replace).
  7. Remove the bolt that attaches the LH front rotor to the LH front hub.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 10 mm socket
    • 2 in extension
  8. Install the hub jack adapter onto the LH front hub and hand-tighten the lug nuts (x5).
  9. Position and raise the underhoist stand to simulate the suspension at ride height.
  10. Measure the distance between the bottom of the fender and the center of the front axle to make sure that the front suspension is set to ride height. The distance should measure 423 mm.
  11. Tighten the bolt and nut that attach the LH strut to the LH front lower lateral link, and then mark the bolt and nut with a paint pen.
    106 Nm (78.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 21 mm deep socket
    • Ratchet/torque wrench
  12. Remove the underhoist stand from underneath the LH front suspension.
  13. Remove the lug nuts (x5) that attach the hub jack adapter, and then remove the hub jack adapter from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Gently tap with a dead blow to aid
  14. Install the bolt that attaches the LH front rotor to the LH front hub.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 10 mm socket
    • 2 in extension
  15. Repeat step 7 through step 14 for the RH side of the vehicle.
  16. Install the front wheels. See Wheel Assembly (Remove and Install).
  17. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust as a separate activity. See Alignment Requirement - Suspension.