2026-07-07

Actuator - Lower Mode - HVAC (Remove and Install)

Correction code 1810050101 FRT 2.52 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2026-07-02: Released new procedure.

Torque Specifications

Table 1. Torque Specifications: Actuator - Lower Mode - HVAC (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
Nuts (x4) that attach the steering column to the cross car beam,
15 Nm (11.1 lbs-ft)
  • Socket 3/8in Dr. 6pt. Std. x 13mm
 Reuse
Bolt that attaches the cross car beam to the HVAC assembly
5.5 Nm (4.1 lbs-ft)
  • Socket 3/8in Dr. 6pt. Std. x 10mm
 Reuse
Bolt that attaches the cross car beam to the upper cowl
25 Nm (18.4 lbs-ft)
  • 3/8in Dr. Open Crowfoot Socket x 13mm
 Reuse
Bolts (x4) that attach the cross car beam to the HVAC assembly
5.5 Nm (4.1 lbs-ft)
  • SKT, 1/4" DR, DEEP, 10MM
 Reuse
Bolts (x2) that attach the cross car beam to the body
25 Nm (18.4 lbs-ft)
  • Socket 3/8in Dr. 6pt. Std. x 13mm
 Reuse
Bolts (x4) that attach the LH and RH cross car beam to the body
29 Nm (21.4 lbs-ft)
  • Socket 3/8in Dr. 6pt. Std. x 15mm
 Reuse
Screws (x2) that secure the lower mode actuator
1.3 Nm (1.0 lbs-ft)
  • Socket 1/4in Dr. 6pt. Std. x 6mm
 Reuse

Remove

  1. Remove the wiper module. See Wiper Module (LHD) (Remove and Replace).
  2. Remove the center console assembly. See Center Console (Remove and Replace).
  3. Remove the LH footwell duct. See Duct - Footwell - LH (Remove and Replace).
  4. Remove the IP carrier. See IP Carrier (Remove and Install).
  5. Remove the LH air wave duct. See Duct - Air Wave - LH (Remove and Replace).
  6. Remove the nuts (x4) that attach the steering column to the cross car beam, then lower the steering column and move it aside.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Socket 3/8in Dr. 6pt. Std. x 13mm
  7. Remove the headliner harness clips (x2) on the LH lower A-pillar.
  8. Remove the headliner harness clips (x2) on the RH lower A-pillar.
  9. Remove the clips that attach the LH front main carpet to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Number of clips on new vehicles may .
  10. Remove the clips that attach the RH front main carpet to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Number of clips on new vehicles may vary
  11. Remove the LH and RH cross car beam brackets. See Beam - Cross Car (LHD) (Remove and Replace).
  12. Remove the bolt that attaches the cross car beam to the HVAC assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Socket 3/8in Dr. 6pt. Std. x 10mm
  13. Remove the bolt that attaches the cross car beam to the upper cowl.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 3/8in Dr. Open Crowfoot Socket x 13mm
  14. Remove the bolts (x4) that attach the cross car beam to the HVAC assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • SKT, 1/4" DR, DEEP, 10MM
  15. Remove the bolts (x2) that attach the cross car beam to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Socket 3/8in Dr. 6pt. Std. x 13mm
  16. Remove the bolts (x4) that attach the LH and RH cross car beam to the body.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Socket 3/8in Dr. 6pt. Std. x 15mm
  17. Remove the wiring harness fixing clips (x2) from the lower part of the cross car beam.
  18. With assistance, partially remove the cross car beam from the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the RH side of the cross car beam for enough space to remove the lower actuator.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pay attention to the datums (x5).
  19. Remove the screws (x2) that secure the lower mode actuator, disconnect the connector, and then remove the actuator from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Socket 1/4in Dr. 6pt. Std. x 6mm

Install

  1. Insert the lower mode actuator into the keyway, connect the actuator connector, and then install the screws (x2) that secure the actuator.
    1.3 Nm (1.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Socket 1/4in Dr. 6pt. Std. x 6mm
  2. With assistance, align the datums (x5) on the beam with the slots on the body and install the cross car beam to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the harness is not squeezed.
  3. Install the wiring harness fixing clips (x2) to the lower part of the cross car beam.
  4. Install the bolts (x4) that attach the LH and RH cross car beam to the body.
    29 Nm (21.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Socket 3/8in Dr. 6pt. Std. x 15mm
  5. Install the bolts that attach the cross car beam to the body.
    25 Nm (18.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Socket 3/8in Dr. 6pt. Std. x 13mm
  6. Install the bolt that attaches the cross car beam to the upper cowl.
    25 Nm (18.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 3/8in Dr. Open Crowfoot Socket x 13mm
  7. Install the bolt that attaches the cross car beam to the HVAC assembly.
    5.5 Nm (4.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Socket 3/8in Dr. 6pt. Std. x 10mm
  8. Install the bolts (x4) that attach the cross car beam to the HVAC assembly.
    5.5 Nm (4.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • SKT, 1/4" DR, DEEP, 10MM
  9. Install the LH and RH cross car beam brackets. See Beam - Cross Car (LHD) (Remove and Replace).
  10. Install the clip that attaches the LH front main carpet to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Number of clips on new vehicles may vary.
  11. Install the clip that attaches the RH front main carpet to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Number of clips on new vehicles may vary
  12. Install the clips (x2) that attach the headliner harness onto the LH lower A-pillar.
  13. Install the clips (x2) that attach the headliner harness onto the RH lower A-pillar.
  14. Position the steering column for installation, then install the nuts (x4) that attach the steering column to the cross car beam.
    15 Nm (11.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Socket 3/8in Dr. 6pt. Std. x 13mm
  15. Install the LH air wave duct. See Duct - Air Wave - LH (Remove and Replace).
  16. Install the IP carrier. See IP Carrier (Remove and Install).
  17. Install the LH footwell duct. See Duct - Footwell - LH (Remove and Replace).
  18. Install the center console assembly. See Center Console (Remove and Replace).
  19. Install the wiper module. See Wiper Module (LHD) (Remove and Replace).