10/04/2024 20:24:40

Jounce Hose - Front Brake - LH (Remove and Replace)

Correction code 3303020132 FRT 0.90 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
Brake fluid dissolves paint. Have clean towels and plenty of water standing by to wash spilled brake fluid off painted surfaces.
Informational PurposesAn informational icon, calling your attention
Note
Dispose of used brake fluid in a manner consistent with local environmental codes.

Torque Specifications

Table 1. Torque Specifications：Jounce Hose - Front Brake - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Nut at the jounce hose bracket
16 Nm (11.8 lbs-ft)
  • ¼ in to 3/8 in adapter
  • Ratchet/torque wrench
  • 12 mm socket
 Reuse
Nut at the body
6 Nm (4.4 lbs-ft)
  • Ratchet/torque wrench
  • Cordless 1/4in Dr Ratchet
  • 10 mm deep socket
 Reuse
Bolt that attaches the flexible brake hose to the brake knuckle
5 Nm (3.7 lbs-ft)
  • Ratchet/torque wrench
  • 10 mm deep socket
 Reuse
Bolt that attaches the flexible brake hose to the brake caliper
42 Nm (31.0 lbs-ft)
  • Ratchet/torque wrench
  • 11 mm 12-point deep socket
 Replace

Remove

  1. Raise and support the vehicle. See GUID-0ECF2493-88F6-48E9-ADBB-9AE1D52E217C.html.
  2. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  3. Remove all four wheels. See Wheel Assembly (Remove and Install).
  4. Position the oil drain under the front LH brake hose.
  5. Remove the bolt securing the LH front brake hose to LH front brake caliper.
    Tip: Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 11 mm 12-point deep socket
    Informational PurposesAn informational icon, calling your attention
    Note
    The bolt and washers (x2) are captive and cannot be reused. Replace the hose assembly if the bolt is loosened or removed.
  6. Remove the bolt securing the LH front brake hose to LH front brake knuckle.
    Tip: Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • 10 mm deep socket
  7. Remove the nut that securing LH front brake line to LH front brake hose.
    Tip: Use of the following tool(s) is recommended:
    • ¼ in to 3/8 in adapter
    • Ratchet/torque wrench
    • 12 mm socket
  8. Remove nut securing LH front brake hose to body, and then remove the hose from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • Cordless 1/4in Dr Ratchet
    • 10 mm deep socket

Install

  1. Position the LH rear flexible brake hose into the vehicle, and then install the nut that attaches the hose to the LH front brake caliper.
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The bolt and washers are captive in the new hose assembly.
    Tip: Use of the following tool(s) is recommended:
    • Ratchet/torque wrench
    • Cordless 1/4in Dr Ratchet
    • 10 mm deep socket
  2. Install the nut that securing LH front brake line to LH front brake hose.
    16 Nm (11.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 3 in extension
    • Ratchet/torque wrench
    • 12 mm socket
  3. Install the bolt securing the LH front brake hose to LH front brake knuckle.
    5 Nm (3.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 3 in extension
    • Ratchet/torque wrench
    • 12 mm socket
  4. Install the bolt securing the LH front brake hose to LH front brake caliper.
    42 Nm (31.0 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 3 in extension
    • Ratchet/torque wrench
    • 12 mm socket
    Informational PurposesAn informational icon, calling your attention
    Note
    The bolt and washers (x2) are captive and cannot be reused. Replace the hose assembly if the bolt is loosened or removed.
  5. Remove the oil drain from under the vehicle.
  6. Perform a brake fluid flush on the brakes. See Brake Fluid Bleed/Flush (Maintenance).