09/11/2023 01:11:21

Toe link - Rear - LH (Remove and Replace)

Correction code 3103030512 FRT 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 1457016-00-A KIT, SPRING COMPRESSOR, GEDORE
  • 1137855-00-A TOOL, REAR RIDE HEIGHT TORQUE, MODEL 3
  • 1081765-00-A 3/4 TON UNDERHOIST STAND
  • 1459409-00-A ADAPTER, HUB JACK, MODEL 3

Torque Specifications

Table 1. Torque Specifications: Toe link - Rear - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt and nut that attach the LH rear toe link to the LH rear suspension knuckle
76 Nm (56.0 lbs-ft)
  • Cordless 3/8in Dr Impact
  • 18 mm socket
  • Flex head ratchet/flex head torque wrench
 Reuse
Bolt and nut that attach the LH rear toe link to the subframe
85 Nm (62.7 lbs-ft)
  • Cordless 3/8in Dr Impact
  • 18 mm deep socket
  • Flex head ratchet/flex head torque wrench
  • 18mm 12pt combination wrench
 Reuse

Remove

  1. Inspect the tires for abnormal wear.
    Informational PurposesAn informational icon, calling your attention
    Note
    Note any abnormal tire wear that could indicate the need for an alignment.
  2. Remove the LH rear wheel. See Wheel Assembly (Remove and Install).
  3. Remove the rear aero shield panel. See Panel - Aero Shield - Rear (Remove and Replace).
  4. Remove the LH rear suspension cover. See Cover - Rear Suspension - LH (Remove and Replace).
  5. Remove the bolt and nut that attach the LH rear toe link to the LH rear suspension knuckle.
    Tip: Use of the following tool(s) is recommended:
    • Cordless 3/8in Dr Impact
    • 18 mm socket
    • Flex head ratchet/flex head torque wrench
  6. Remove the bolt and nut that attach the LH rear toe link to the subframe.
    Tip: Use of the following tool(s) is recommended:
    • Cordless 3/8in Dr Impact
    • 18 mm deep socket
    • Flex head ratchet/flex head torque wrench
    • 18mm 12pt combination wrench
  7. Remove the LH rear toe link from vehicle.

Install

  1. Position the LH rear toe link onto the subframe, and then install and hand-tighten the bolt and nut.
    Tip: Recommend assistance when performing this step.
  2. Position the LH rear toe link onto the knuckle, and then install and hand-tighten the bolt and nut.
    Tip: Recommend assistance when performing this step.
  3. Install a spring compressor onto the LH rear suspension spring:
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Springs in a compressed state are under large amounts of energy. Refer to the Tool Profile for the spring compressor kit prior to performing this step for additional warnings and cautions.
  4. Remove the bolt that attaches the LH rear brake rotor to the hub.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 10 mm socket
    • 2 in extension
  5. Install the hub jack adapter onto the LH rear hub and hand-tighten the lug nuts (x5).
  6. Position and raise the underhoist stand to simulate the suspension at ride height.
  7. Adjust the underhoist stand and/or spring compressor until the lower beam of the rear ride height torque tool rests against the bottom edge of the lower aft link, as illustrated.
  8. Measure the distance between the bottom of the quarter panel and the center of the rear axle to make sure that the rear suspension is set to ride height. The distance should measure 378 mm.
  9. Tighten the bolt and nut that attach the LH rear toe link to the LH rear suspension knuckle. Mark the bolt with a paint pen.
    76 Nm (56.0 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless 3/8in Dr Impact
    • 18 mm socket
    • Flex head ratchet/flex head torque wrench
  10. Tighten the bolt and nut that attach the LH rear toe link to the subframe. Mark the bolt with a paint pen.
    85 Nm (62.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless 3/8in Dr Impact
    • 18 mm deep socket
    • Flex head ratchet/flex head torque wrench
    • 18mm 12pt combination wrench
  11. Remove the underhoist stand from underneath the LH rear suspension.
  12. Remove the lug nuts (x5) that attach the hub jack adapter, and then remove the hub jack adapter from the vehicle.
  13. Install the bolt that attaches the LH rear brake rotor to the LH rear hub.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 10 mm socket
    • 2 in extension
  14. Remove the spring compressor from the LH rear suspension spring:
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Be careful while unloading the spring. Hold the spring horizontally and facing away from you.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Springs in a compressed state are under large amounts of energy. Refer to the Tool Profile for the spring compressor kit prior to performing this step for additional warnings and cautions.
  15. Install the rear aero shield panel. See Panel - Aero Shield - Rear (Remove and Replace).
  16. Install the LH rear suspension cover. See Cover - Rear Suspension - LH (Remove and Replace).
  17. Install the LH rear wheel. See Wheel Assembly (Remove and Install).
  18. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust as a separate activity. See Alignment Requirement - Suspension.