28/01/2024 23:32:16

Airbag - Curtain - RH (RHD) (Remove and Replace)

Correction code 2001108022 FRT 1.26 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Make sure LV power has been disconnected for at least 2 minutes before disconnecting the electrical harness from Supplementary Restraint System (SRS) components, such as Restraint Control Module, sensors, airbags, etc. Failure to do so can result in unintended safety system behaviors. For more information on SRS precautions, see Airbag and Supplementary Restraint System (SRS) Precautions.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Supplementary Restraint System (SRS) components can be hazardous if not handled properly. For more information on SRS precautions, see Airbag and Supplementary Restraint System (SRS) Precautions.

Torque Specifications

Table 1. Torque Specifications: Airbag - Curtain - LH (LHD) (Remove and Replace)Airbag - Curtain - RH (RHD) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x10) that attach the LH/RH curtain airbag to the body
9 Nm (6.6 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 2 in extension
  • 10 mm socket
  • Ratchet/torque wrench
 Reuse
Informational PurposesAn informational icon, calling your attention
Note
Do NOT use impact tool to install these self-tapping bolts.

Remove

  1. Remove the headliner. See Headliner (Remove and Replace).
  2. Move the front seats forward.
  3. Disconnect LV power. See LV Battery - Li-lon (Disconnect and Connect).
  4. Lift the white tab to disconnect the RH curtain airbag electrical harness connector.
  5. Remove the bolts (x10) that attach the RH curtain airbag to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do NOT use impact tool to remove these self-tapping bolts.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 2 in extension
    • 10 mm socket
    • Ratchet/torque wrench
  6. Carefully release the clips (x8) that secure the RH curtain airbag, and then remove the airbag from the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    If any clips are damaged, the airbag must be replaced.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The airbag should always be handled by the igniter, and the igniter should never be left dangling.

Install

  1. Install the RH curtain airbag to the side rail, and then carefully fasten the clips (x8) that attach the airbag to the side rail.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    If any clips are damaged, the airbag must be replaced.
  2. Install and hand-tighten the self-tapping bolts (x10) that attach the RH curtain airbag to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure that the tuner maintains a certain distance from the airbag and do not interfere each other.
  3. Tighten the bolts (x10) that attach the RH curtain airbag to the body.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Do NOT use impact tool to install these self-tapping bolts.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 2 in extension
    • 10 mm socket
    • Ratchet/torque wrench
  4. Connect the RH curtain airbag electrical harness connector.
  5. Connect 12V power. See LV Battery - Li-lon (Disconnect and Connect).
  6. Move the front seats backward and the seat backs downward.
  7. Install the headliner. See Headliner (Remove and Replace).