17/09/2024 07:28:02

Brake Rotor - Rear (Base Brakes) - LH (Remove and Replace)

Correction code 3301020212 FRT 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-09-17: Added EPB Service Mode reference.
  • 2024-05-31: Added caution for correct rear brake hose installation.
  • Brake Caliper S-Hook
Informational PurposesAn informational icon, calling your attention
Note
For detailed brake specifications, see Brakes.

Torque Specifications

Table 1. Torque Specifications: Brake Rotor - Rear (Base Brakes) - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) that attach the LH rear brake caliper to the LH rear knuckle
83 Nm (61.2 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • External Torx E18
  • 3 in extension
  • Ratchet/torque wrench
 Replace
Bolt that attaches the LH rear brake rotor to the hub
5 Nm (3.7 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 10 mm socket
  • 2 in extension
 Reuse

Remove

  1. Raise and support the vehicle. See GUID-0ECF2493-88F6-48E9-ADBB-9AE1D52E217C.html.
  2. Open the LH front door and lower the LH front window.
  3. Place the vehicle into EPB Service Mode. See Parking Brake - Caliper - Rear - LH (Release).
  4. Remove the LH rear wheel. See Wheel Assembly (Remove and Install).
  5. Disconnect the LH rear EPB caliper connector.
  6. Remove and discard the bolts (x2) that attach the LH rear caliper to the LH rear knuckle, remove the caliper from the knuckle, and allow the caliper to hang from an S-hook.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • External Torx E18
    • 3 in extension
    • Ratchet/torque wrench
  7. Remove the bolt that attaches the LH rear brake rotor to the hub.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 10 mm socket
    • 2 in extension
  8. Remove the LH rear rotor from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Store the rotor face down to reduce likelihood of damage to the rotor face.

Install

  1. Install the LH rear rotor onto the vehicle.
  2. Install the bolt that attaches the LH rear brake rotor to the LH rear hub.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 10 mm socket
    • 2 in extension
  3. Install new bolts (x2) that attach the LH rear caliper to the LH rear knuckle.
    83 Nm (61.2 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • External Torx E18
    • 3 in extension
    • Ratchet/torque wrench
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    To prevent damage to the flexible brake hose, make sure that the brake hose can bend forward and does not make contact with the wheel arch liner when the vehicle is lowered.
  4. Connect the LH rear EPB caliper connector.
  5. Install the LH rear wheel. See Wheel Assembly (Remove and Install).
  6. Exit the vehicle from "Towing" mode.
  7. Raise the LH front window and close the LH front door.
  8. Lower the vehicle. See GUID-0ECF2493-88F6-48E9-ADBB-9AE1D52E217C.html.