15/05/2024 23:11:05

Control Arm - Upper - Front - LH (Remove and Replace)

Correction code 3101030012 FRT 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 1450399-00-A Tool, FUCA Ride Height, Model 3

Torque Specifications

Table 1. Torque Specifications: Control Arm - Upper - Front - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x4) that attach the LH front upper control arm mount to the body
35 Nm (25.8 lbs-ft)
62 Nm (45.7 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 13 mm socket
  • 15 mm socket
  • Flex head ratchet/flex head torque wrench
 Reuse
Nut that attaches the front stabilizer bar end link to the LH front strut
98 Nm (72.3 lbs-ft)
  • 18 mm combination wrench
  • Torx T40 socket
  • Cordless Ratchet/Impact Driver
  • Ratchet/torque wrench
 Replace
Bolt and nut that attach the LH front upper control arm to the knuckle
56 Nm (41.3 lbs-ft)
  • 15 mm combination wrench
  • Torx T50 socket
  • Cordless Ratchet/Impact Driver
  • Flex head ratchet/flex head torque wrench
 Nut: Replace; Bolt: Reuse
Bolts (x2) that attach the LH front upper control arm to the front upper control arm mount
50 Nm (36.9 lbs-ft)
  • 13 mm deep socket
  • Cordless Ratchet/Impact Driver
  • Flex head ratchet/flex head torque wrench
 Reuse

Remove

  1. Inspect the vehicle for abnormal tire wear that might indicate the need for a wheel alignment. Note any findings.
  2. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  3. Remove the cabin intake duct. See Assembly - Fresh Air Gutter - HVAC (Remove and Replace).
  4. Remove the access panel. See Cover - Hood Latch (Remove and Replace).
  5. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  6. Remove the LH shock tower cover. See Cover - Shock Tower - LH (Remove and Install).
  7. Release the clip that attaches the cowl screen panel to the vehicle.
  8. Use a paint pen to mark the position of the bolts (x4) that attach the LH front upper control arm mount to the body, and then remove the bolts.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 13 mm socket
    • 15 mm socket
    • Flex head ratchet/flex head torque wrench
  9. Remove the LH front wheel. See Wheel Assembly (Remove and Install).
  10. Release the clips (x2) that attach the LH front wheel speed sensor harness to the LH front upper control arm, and then set the harness aside.
  11. Remove and discard the nut that attaches the front stabilizer bar end link to the LH front strut and separate the end link from the strut.
    Informational PurposesAn informational icon, calling your attention
    Note
    Counter-hold the ball joint while loosening the nut.
    Tip: If needed, use a pry bar to release the end link.
    Tip: Use of the following tool(s) is recommended:
    • 18 mm combination wrench
    • Torx T40 socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench
  12. Remove the bolt and nut that attach the LH front upper control arm to the knuckle, and then discard the nut.
    Informational PurposesAn informational icon, calling your attention
    Note
    Compress the upper control arm ball joint downwards to help release the bolt.
    Tip: Use of the following tool(s) is recommended:
    • 15 mm combination wrench
    • Torx T50 socket
    • Cordless Ratchet/Impact Driver
    • Flex head ratchet/flex head torque wrench
  13. Pull the LH front spring and damper assembly outboard so that the front upper control arm mount clears the wheel arch liner.
    Informational PurposesAn informational icon, calling your attention
    Note
    Maneuver the right side of the LH front upper control arm first.
    Tip: Hold the front upper control arm mount and use thumbs to push the wheel arch liner past the mount.
  14. Remove the bolts (x2) that attach the LH front upper control arm to the front upper control arm mount.
    Tip: Use of the following tool(s) is recommended:
    • 13 mm deep socket
    • Cordless Ratchet/Impact Driver
    • Flex head ratchet/flex head torque wrench
  15. Remove the LH front upper control arm from the front upper control arm mount.

Install

  1. Position the LH front upper control arm into the front upper control arm mount, and then install and hand-tighten the bolts (x2) that attach the control arm to the mount.
  2. Install the FUCA ride height tool onto the front upper control arm mount at the rear outer mounting hole.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the LH front upper control arm is between the FUCA mount and the ride height tool.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  3. Hold the front upper control arm against the plate of the FUCA ride height tool and tighten the bolts (x2) that attach the LH front upper control arm to the front upper control arm mount.
    50 Nm (36.9 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    To prevent personal injury when torquing bolts and simultaneously holding components in position, pay extra attention to the angle and trajectory of the tool used.
    Informational PurposesAn informational icon, calling your attention
    Note
    After tightening, check the measurement again and adjust if necessary.
    Tip: Use of the following tool(s) is recommended:
    • 13 mm deep socket
    • Cordless Ratchet/Impact Driver
    • Flex head ratchet/flex head torque wrench
  4. Remove the FUCA ride height tool from the front upper control arm mount.
  5. Move the LH coil spring module and front upper control arm mount assembly into position, making sure the control arm mount bolt holes are aligned with the bolt holes on the body.
  6. Install the bolts (x4) that attach the LH front upper control arm mount to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure the larger and smaller bolts are installed in the correct locations.
    Informational PurposesAn informational icon, calling your attention
    Note
    Line up the bolts with marks created during removal.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 13 mm socket
    • 15 mm socket
    • Flex head ratchet/flex head torque wrench
  7. Position the front stabilizer end link onto the LH front strut, and then install a new nut that attaches the front stabilizer end link to the LH front strut.
    98 Nm (72.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Counter-hold the ball joint while torquing the nut.
    Tip: If needed, use a pry bar to help position the end link.
    Tip: Use of the following tool(s) is recommended:
    • 18 mm combination wrench
    • Torx T40 socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench
  8. Position the LH front control arm to the knuckle, and then install the nut and a new bolt that attach the LH front upper control arm to the knuckle.
    56 Nm (41.3 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 15 mm combination wrench
    • Torx T50 socket
    • Cordless Ratchet/Impact Driver
    • Flex head ratchet/flex head torque wrench
  9. Install the clips (x2) that attach the LH front wheel speed sensor harness to the LH front upper control arm.
  10. Install the LH front wheel. See Wheel Assembly (Remove and Install).
  11. Install the clip that attaches the cowl screen panel to the vehicle.
  12. Install the LH shock tower cover. See Cover - Shock Tower - LH (Remove and Install).
  13. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  14. Install the access panel. See Cover - Hood Latch (Remove and Replace).
  15. Install the cabin intake duct. See Assembly - Fresh Air Gutter - HVAC (Remove and Replace).
  16. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  17. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust as a separate activity. See Alignment Requirement - Suspension.