10/05/2024 01:33:01

Touchscreen - Rear (Remove and Replace)

Correction code 2107010212 FRT 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Touchscreen - Rear (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x5) that attach the rear display to the rear end module
1 Nm (.7 lbs-ft)
  • Torx T20 socket
  • Cordless Ratchet/Impact Driver
  • 4 in extension
  • Torque Wrench Hexagon - 1060071-00-A (for installation only)
 Reuse

Remove

  1. Remove the center console phone dock. See Phone Dock (Clip) - Interior Trim - Center Console (Remove and Replace).
  2. Remove center console rear end panel. See Panel - Rear End - Center Console (Remove and Replace)
  3. Remove LH rear side panel from center console assembly. See Panel - Rear Side - Center Console - LH (Remove and Replace).
  4. Remove LH front side panel from center console assembly. See Carpet - Side - Center Console - LH (Remove and Replace).
  5. Remove LH center décor trim. See Decor Trim - Center Console - LH (Remove and Replace).
  6. Repeat step 3 through step 5 for the RH side of the vehicle.
  7. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  8. Disconnect LV battery power. See LV Battery - Li-lon (Disconnect and Connect)
  9. Remove the rear end module assembly. See Module - Rear End - Center Console (Remove and Replace)
    Informational PurposesAn informational icon, calling your attention
    Note
    No need to remove the rear end module from the assembly.
  10. Remove the bolts (x5) that attach the rear display to the rear end module assembly, and then remove the rear display from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • Cordless Ratchet/Impact Driver
    • 4 in extension
    • Torque Wrench Hexagon - 1060071-00-A (for installation only)

Install

  1. Install the bolts (x5 ) that attach the rear display to the rear end module.
    1 Nm (.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 socket
    • Cordless Ratchet/Impact Driver
    • 4 in extension
    • Torque Wrench Hexagon - 1060071-00-A (for installation only)
  2. Install the rear end module assembly. See Module - Rear End - Center Console (Remove and Replace)
  3. Connect LV battery power. See LV Battery - Li-lon (Disconnect and Connect)
  4. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  5. Install LH center console décor trim. See Decor Trim - Center Console - LH (Remove and Replace).
  6. Install LH center console front side panel. See Carpet - Side - Center Console - LH (Remove and Replace).
  7. Install LH center console rear side panel. See Panel - Rear Side - Center Console - LH (Remove and Replace).
  8. Repeat step 5 through step 7 for the RH side of the vehicle.
  9. Install the center console rear end panel. See Panel - Rear End - Center Console (Remove and Replace)
  10. Install the center console phone dock. See Phone Dock (Clip) - Interior Trim - Center Console (Remove and Replace).
  11. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  12. In Toolbox, click the Actions/Autodiag tab, and then type "PING-BASH_DISPLAY" into the search field.
  13. Click PING-BASH_DISPLAY-REARvia Toolbox: (link), click Run, and allow the routine to complete.
  14. Disconnect the laptop with Toolbox 3 from the vehicle. See Toolbox 3 (Connect and Disconnect).