01/04/2024 14:05:28

Touchscreen - Front (Remove and Replace)

Correction code 2107123022 FRT 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 1773092-00-A Diagnostic Harness Adapter - All Models
  • 1930388-00-A OBD II TO RJ45 NETWORK PORT
Table 1. Torque Specifications: Touchscreen - Front (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Patch bolts (x2) that attach the touchscreen to the instrumental panel carrier
16 Nm (11.8 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 2 in extension
  • 10 mm socket
  • Ratchet/torque wrench
 Replace
Bolts (x2) that attach the housing neck to the touchscreen
3 Nm (2.2 lbs-ft)
  • Torx T30 socket
  • 2 in extension
  • Ratchet/torque wrench
 Reuse

Remove

  1. Open the LH front door and lower the LH front window.
  2. Disconnect the LV battery power. See LV Battery - Li-lon (Disconnect and Connect).
  3. Remove the instrumental panel service panel. See Service Panel - Instrument Panel (Remove and Replace).
  4. Disconnect the temperature sensor connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  5. Remove and discard the patch bolts (x2) that attach the center display to the instrumental panel carrier.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 2 in extension
    • 10 mm socket
    • Ratchet/torque wrench
  6. Disconnect the harness connectors (x2) from the touchscreen.
  7. Remove the touchscreen from the vehicle.

Install

  1. Position the touchscreen into the vehicle, and then connect the harness connectors (x2) to the touchscreen.
  2. Install the new patch bolts (x2) that attach the center display to the instrumental panel carrier.
    16 Nm (11.8 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 2 in extension
    • 10 mm socket
    • Ratchet/torque wrench
  3. Connect the temperature sensor connector.
  4. Install the instrumental panel service panel. See Service Panel - Instrument Panel (Remove and Replace).
  5. Connect the LV battery power. See LV Battery - Li-lon (Disconnect and Connect).
  6. Locally connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect).
  7. On the laptop, select Actions/Autodiag, and then search for "PING-BASH_DISPLAY". Select PING-BASH_DISPLAYvia Toolbox: (link), click Run, and allow the routine to complete.
  8. Search for "PROC_ICE_X_GATEWAY-SAFE-REBOOT", select PROC_ICE_X_GATEWAY-SAFE-REBOOTvia Toolbox: (link), click Run, and allow the routine to complete.
  9. Remove the diagnostic cable from the port to disconnect Toolbox 3.0 from the vehicle.
  10. Raise the LH front window and close the LH front door.