2026-06-19

Perform General Inspection (Inspection)

Correction code 00030700 FRT 0.90 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Warning

This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.

2026-06-18: Released new procedure.

Procedure

Function check LH front door (exterior)

Note
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check LH front door (interior)

Note
Inspect and note functionality for the interior door release, puddle lamps, and manual release cable, From inside look for interference with other components, noises such as creaks, groans and clicks, pauses or incomplete actions
Function check all windows from master switch

Note
Document any abnormal operation/noises
Function check wipers and spray jets

Note
Ensure hood and doors are closed prior to activating wipers, Inspect and note functionality for wipers and wiper jets, Check for full range of motion, speed of motion, interference with other components, noises such as creaks, groans and clicks, pauses or incomplete actions
Function check all driver controls

Note
Shift stalk, turn signals, steering wheel scroll wheels, horns
Function check steering column through UI

Note
Move the column to its extreme position in each direction using steering wheel buttons, Return to original position
Function check the exterior lights

Note
Recommend assistance, inspect and note functionality of Headlight (LH and RH), Side Repeater (LH and RH), Taillight (LH and RH), CHMSL, Fog Light (LH and RH), Reverse Light (LH and RH), Front Turn Signal (LH and RH), Rear Turn Signal (LH and RH)
Function check hazard light switch
Function check LH rear door (exterior)

Note
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check RH rear door (exterior)

Note
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check RH front door (exterior)

Note
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Open hood
Remove rear apron

Note
14x clips
Remove fresh air gutter assembly

Note
3x clips
Check coolant level in reservoir
Check brake fluid level
Fill washer reservoir with fluid
Install fresh air gutter assembly

Note
3x clips
Install rear apron

Note
14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips
Close hood
Raise and support vehicle

Note
remove charging equipment
Raise vehicle partially and lower lift onto locks

Note
Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, Otherwise vehicle may tilt to the side
Check all four tire pressures manually

Note
4x tires, 4x caps, Set to specification if necessary, Refer to the "Tire and Loading Information" label located on the driver side B-pillar, Inspect wheels and tires for any bulges or damage while checking/setting pressures
Record tread depth for LH front tire

Note
Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
Record tread depth for RH front tire

Note
Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
Record tread depth for LH rear tire

Note
Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
Record tread depth for RH rear tire

Note
Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
Measure and record LH rear brake pad thickness

Note
Recommend replacement if 2mm or less, Check both inboard and outboard pads
Inspect LH rear brake rotor condition

Note
Check for excessive rust or wear, Minimum spec 26mm
Measure and record RH rear brake pad thickness

Note
Recommend replacement if 2 mm or less, Check both inboard and outboard pads
Inspect RH rear brake rotor condition

Note
Check for excessive rust or wear, Minimum spec 26mm
Measure and record RH front brake pad thickness

Note
Recommend replacement if 2mm or less, Check both inboard and outboard pads
Inspect RH front brake rotor condition

Note
Check for excessive rust or wear, Minimum spec 30mm
Measure and record LH front brake pad thickness

Note
Recommend replacement if 2mm or less, Check both inboard and outboard pads
Inspect LH front brake rotor condition

Note
Check for excessive rust or wear, Minimum spec 30mm
Raise vehicle fully and lower lift onto locks

Note
Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged
Remove bolts securing front aero shield

Note
7x bolts, 10mm, 5 Nm
Remove front aero shield from studs

Note
2x nuts, 15mm, 8 Nm
Remove rear aero shield clips

Note
2x clips, One clip on LH side wheel liner, One clip on RH side wheel liner
Remove rear aero shield

Note
11x bolts, 10mm, 5 Nm
Remove LH rear suspension cover

Note
1x bolt, 10mm, 6 Nm, 2x tabs
Remove RH rear suspension cover

Note
1x bolt, 10mm, 6 Nm, 2x tabs
Perform visual inspection of HV battery enclosure

Note
Check for any dents, scrapes, or other damage
Inspect underside of vehicle for fluid leaks
Perform inspection of steering components

Note
Check steering gear joints, fasteners, and electrical connections, Verify components are not bent or damaged
Perform inspection of front suspension components

Note
Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
Perform inspection of rear suspension components

Note
Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
Install RH rear suspension cover

Note
1x bolt, 10mm, 6 Nm, 2x tabs
Install LH rear suspension cover

Note
1x bolt, 10mm, 6 Nm, 2x tabs
Install rear aero shield

Note
11x bolts, 10mm, 5 Nm, Apply Loctite 222 onto rear aero shield bolts before installing
Install rear aero shield

Note
2x clips, One clip on LH side wheel liner, One clip on RH side wheel liner
Position front aero shield onto vehicle and secure with two nuts

Note
2x nuts, 15mm, 8 Nm, Hand-tighten the nuts to temporarily hold the panel in place
Install front aero shield bolts

Note
7x bolts, 10mm, 5 Nm, Apply Loctite 222 onto bolts before installing
Lower vehicle until tires are touching ground

Note
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
Raise all four windows
Close all four doors
Perform a road test using a series of ABS-active stops and ensure proper brake pedal feel and performance

Note
The vehicle must stop completely within 25 feet (7.6 meters) at 20 mph (32 kph), Confirm that no excessive vibration or noise is present
Inspect vehicles alignment

Note
Confirm steering wheel is straight and no vibrations or noises are felt or heard from the suspension, On a flat road, at 35 mph (56 kph), the vehicle does not pull in either direction

Perform General Inspection (Inspection)

Procedure

Figure 1

Figure 2

Figure 3