23/01/2024 19:58:18

Door - Rear - LH (Remove and Install)

Correction code 1010025041 FRT 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-01-24: Added a note in case that the shouldered / tapered bolts are not allowing for successful adjustment.

Torque Specifications

Table 1. Torque Specifications: Door - Rear - LH (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the LH rear door check strap to the body
24 Nm (17.7 lbs-ft)
  • Cordless Ratchet/Impact Driver
  • 4 in extension
  • Torx T40 socket
  • Ratchet/torque wrench
 Reuse
Bolts (x4) that attach the LH rear door to the vehicle
24 Nm (17.7 lbs-ft)
  • 10 mm socket
  • Ratchet/torque wrench
 Reuse

Remove

  1. Open the rear LH door, and fully lower the window.
  2. Release the clips (x4) of the rear LH door electrical harness seal at the B-pillar, and pull the wiring harness out of the B-pillar bulkhead.
  3. Disconnect the LH rear door harness connector from the LH body harness.
  4. Remove the bolt that attaches the LH rear door check strap to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Unbolting the door check allows the door to swing freely beyond opening limits.
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 4 in extension
    • Torx T40 socket
    • Ratchet/torque wrench
  5. With assistance, remove the bolts (x4) that attach the LH rear door assembly to the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • Ratchet/torque wrench

Install

  1. With assistance, hand-tighten the bolts (x4) that attach the LH rear door assembly to the vehicle.
  2. Install the bolt that attaches the door check to the B-pillar.
    24 Nm (17.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Cordless Ratchet/Impact Driver
    • 4 in extension
    • Torx T40 socket
    • Ratchet/torque wrench
  3. Connect the LH rear door harness connector from the LH body harness.
  4. Secure the tabs (x4) that attach the LH rear door harness seal to the B-pillar.
  5. Close the LH rear door and check for gap/flushness.
    Informational PurposesAn informational icon, calling your attention
    Note
    If the shouldered / tapered bolts are not allowing for successful adjustment, replace the selected shouldered / tapered bolts with 1063260-00-C. Adjust the LH rear door, if necessary. Refer to CVIS for current specifications.
  6. Tighten the bolts (x4) that attach the LH rear door assembly to the vehicle.
    24 Nm (17.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • 10 mm socket
    • Ratchet/torque wrench
  7. Raise the rear LH window and close LH rear door.