2025-11-11

Stabilizer Bar - Front (Remove and Replace)

Correction code 3101062012 FRT 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2025-11-10: An inflatable bag is installed between the front stabilizer bar and front valance for sufficient working space, replacing the need to fully remove the front valance.

Torque Specifications

Table 1. Torque Specifications: Stabilizer Bar - Front (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Nuts that attach the LH and RH front stabar links to the front stabar
98 Nm (72.3 lbs-ft)
  • 18 mm socket
 Replace 1111543-00-A
LH and RH nuts (x4) that attach the front stabar to the front subframe
35 Nm (25.8 lbs-ft)
  • 15 mm deep socket
 Replace 1044388-00-B

Remove

  1. Remove the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  2. Remove the push clips (x6) that attach the LH and RH sides of the valance to the wheel arch liners.
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove the outer clips as necessary to allow for easier access to the nuts behind the wheel liner.
  3. Install an inflatable bag vertically between the front stabilizer bar and front valance to ensure sufficient working space.
  4. Remove and discard the nuts (x2) that attach the LH and RH front stabar links to the front stabar.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 18 mm socket
    Figure 1. LH Shown, RH Similar
  5. Move the LH and RH front stabar links aside.
    Figure 2. LH Shown, RH Similar
  6. With assistance, remove and discard the LH and RH nuts (x4) that attach the front stabar to the front subframe.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm deep socket
    Figure 3. LH Shown, RH Similar
  7. Remove the stabilizer bar from the vehicle.

Install

  1. Position the front stabar to the front subframe, and then install new LH and RH nuts (x4) (1044388-00-B) to attach the front stabar to the front subframe.
    35 Nm (25.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Mark after torque.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 15 mm deep socket
    Figure 4. LH Shown, RH Similar
  2. Position the LH and RH front stabar links to the front stabar.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull down the stabar as needed to allow the end links to engage.
  3. Install new nuts (x2) (1111543-00-A) to attach the LH and RH front stabar links to the front stabar.
    98 Nm (72.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Mark after torque.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 18 mm socket
    Figure 5. LH Shown, RH Similar
  4. Remove the inflatable bag.
  5. Install the push clips (x6) that attach the LH and RH sides of the valance to the wheel liners.
  6. Install the front aero shield panel. See .