Check Strap - Door - Front - LH (Remove and Replace)
Correction code
1133010012
FRT
0.30
NOTE: Unless
otherwise explicitly stated in the procedure, the above correction code and
FRT reflect all of the work required to perform this procedure, including
the linked procedures. Do
not stack correction codes unless explicitly told to do so.
NOTE: See Flat Rate
Times to learn more about FRTs and how
they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com.
NOTE: See Personal Protection
to make sure wearing proper PPE when performing the below procedure.
NOTE: See Ergonomic Precautions for safe and
healthy working practices.
- 1454796-00-A TOOLKIT, WINDOW SWITCH
Torque Specifications
| Description | Torque Value | Recommended Tools | Reuse/Replace | Notes |
|---|---|---|---|---|
| Bolts (x4) that attach the front door speaker to the LH front door |
![]() 4 Nm (2.9 lbs-ft) |
|
Reuse | |
| Bolt that attaches the LH front door check strap to the A-pillar |
![]() 24 Nm (17.7 lbs-ft) |
|
Reuse | |
| Nuts (x2) that attach the check strap to the LH front door |
![]() 10 Nm (7.4 lbs-ft) |
|
Reuse |
Remove
- Remove the LH front door reflector. See Reflector - Door - Front - LH (Remove and Replace).
- Remove the LH front door tweeter. See Tweeter - Front Door - LH (Remove and Replace).
- Remove the LH front door puddle light. See Puddle Lamp - Front Door (LH) (Remove and Replace).
- Remove the LH front door trim panel. See Panel - Door Trim - Front - LH (Remove and Replace).
-
Connect the window switch
tool to the LH front door harness and fully raise the front LH door
window.
-
Disconnect the electrical connector from the front door speaker.
-
Remove the bolts (x4) and
tabs (x4) that attach the front door speaker to the LH front door, and then
remove the speaker.
TIpUse of the following tool(s) is recommended:
- 8 mm socket
-
Remove the bolt that attaches the LH front door check strap to the
A-pillar.
TIpUse of the following tool(s) is recommended:
- 13 mm socket
-
Use a plastic trim to release the clips (x3) that attach the LH front door
check strap to the LH front door.
-
Remove the nuts (x2) that attach the check strap to the LH front
door.
TIpUse of the following tool(s) is recommended:
- 10 mm 12-point deep socket
-
Reach inside the speaker bracket opening and remove the check strap from
the vehicle.
Install
-
Reach inside the speaker bracket opening and install the check strap to the
vehicle.
-
Install the nuts (x2) that attach the check strap to the LH front
door.
10 Nm (7.4 lbs-ft)TIpUse of the following tool(s) is recommended:- 10 mm 12-point deep socket
-
Fasten the clips (x3) that attach the LH front door check strap to the LH
front door.
-
Install the bolt that attaches the LH front door check strap to the
A-pillar.
24 Nm (17.7 lbs-ft)TIpUse of the following tool(s) is recommended:- 13 mm socket
-
Install the bolts (x4) and
tabs (x4) that attach the front door speaker to the LH front door.
4 Nm (2.9 lbs-ft)TIpUse of the following tool(s) is recommended:- 8 mm socket
-
Connect the electrical connector to the front door speaker.
-
Fully lower the LH front door window and disconnect the window switch tool
from the LH front door harness.
- Install the LH front door trim panel. See Panel - Door Trim - Front - LH (Remove and Replace).
- Install the LH front door puddle light. See Puddle Lamp - Front Door (LH) (Remove and Replace).
- Install the LH front door reflector. See Reflector - Door - Front - LH (Remove and Replace).
- Install the LH front door tweeter. See Tweeter - Front Door - LH (Remove and Replace).