17/10/2023 18:50:08

Handle - Seat Back - 2nd Row - RH (Remove and Replace)

Correction code 1305020072 FRT 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Handle - Seat Back - 2nd Row - RH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x2) hat attach the RH 2nd row seat back handle to the seat back frame
2 Nm (1.5 lbs-ft)
  • Torx T25 socket
  • Cordless Ratchet/Impact Driver
  • Ratchet/torque wrench
Reuse

Remove

  1. Remove the RH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
  2. Remove the 2nd row lower seat cushion. See Seat Cushion - 2nd Row (Remove and Replace).
  3. Remove the RH 2nd row seat back. See Seatback - 2nd Row - RH (Remove and Replace).
  4. Remove the RH 2nd row seat back hinge bracket. See Bracket - Hinge - Seat Back - 2nd Row (Remove and Replace).
  5. Remove the RH 2nd row escutcheon. See Escutcheon - Seat Belt - Center (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    There are 2 clips in the RH 2nd row escutcheon.
  6. Remove the RH 2nd row seat back latch release bezel. See Bezel - Handle - Seat Back - 2nd Row - RH (Remove and Replace).
  7. Unzip the RH 2nd row seat back upholstery cover.
  8. Put the electrical harness through the RH 2nd row seat back upholstery cover.
  9. Release the lower portion of the RH 2nd row seat back upholstery trim cover from the pivot bar.
  10. Remove the bolts (x2) that attach the RH 2nd row seat back handle to the seat back frame.
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench
  11. Remove the RH 2nd row seat back assembly from the frame.
  12. Release the clips (x2) that attach the RH 2nd row seat back latch control cable to the RH 2nd row seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Release the clips based on the marked order.
  13. Remove the clip that attaches the RH 2nd row seat back handle assembly to the frame, and then remove the handle assembly from the frame.

Install

  1. Install the clip that attaches the RH 2nd row seat back handle assembly to the frame.
  2. Install the clips (x2) that attach the RH 2nd row seat back latch control cable to the RH 2nd row seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Install the clips based on the marked order.
  3. Install the RH 2nd row seat back assembly to the frame.
  4. Install the bolts (x2) that attach the RH 2nd row seat back handle to the seat back frame.
    2 Nm (1.5 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T25 socket
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench
  5. Install the lower portion of the RH seat back upholstery cover to the pivot bar.
  6. Put the electrical harness through the RH seat back upholstery cover.
  7. Zip the RH 2nd row seat back cover.
  8. Install the RH 2nd row seat back latch release bezel. See Bezel - Handle - Seat Back - 2nd Row - RH (Remove and Replace).
  9. Install the RH 2nd row escutcheon. See Escutcheon - Seat Belt - Center (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    Note
    There are 2 clips in the RH 2nd row escutcheon.
  10. Install the RH 2nd row seat back hinge bracket. See Bracket - Hinge - Seat Back - 2nd Row (Remove and Replace).
  11. Install the RH 2nd row seat back. See Seatback - 2nd Row - RH (Remove and Replace).
  12. Install the 2nd row lower seat cushion. See Seat Cushion - 2nd Row (Remove and Replace).
  13. Install the RH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).