09/07/2024 18:51:31

Phone Dock (Screw) - Interior Trim - Center Console (Remove and Replace)

Correction code 1519011222 FRT 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

Torque Specifications

Table 1. Torque Specifications: Phone Dock (Screw) - Interior Trim - Center Console (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Screws (x2) that attach the phone dock to the center console assembly
1.2 Nm (.9 lbs-ft)
  • Torx T20 bit
  • 2 in extension
  • Ratchet/torque wrench
 Reuse
Screws (x3) that attach the inductive charger to the phone dock.
1 Nm (.7 lbs-ft)
  • Torx T20 bit
  • Ratchet/torque wrench
 Reuse

Remove

  1. Tilt the rear of the center console upwards, and pull the center console towards the rear of the vehicle. See Center Console (Remove and Replace).
  2. Remove the screws (x2) that attach the phone dock to the center console assembly.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 bit
    • 2 in extension
    • Ratchet/torque wrench
  3. Disconnect the electrical connector, and then remove the phone dock from the instrument panel.
  4. Release the clips (x2), screw gaskets (x2), and guide tabs (x6) that attach the phone dock to the center console.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the phone dock assembly out from the bottom side along the tilt angle of the phone dock.
  5. Remove the screws (x3) that attach the inductive charger to the phone dock.
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 bit
    • Ratchet/torque wrench
  6. Release the tabs (x2), datums (x2) and clips (x2) that attach the inductive charger to the phone dock, and then remove the inductive charger from the phone dock.
    Informational PurposesAn informational icon, calling your attention
    Note
    Angle the inductive charger up and slide out of the phone dock.

Install

  1. Fasten the tabs (x2), datums (x2) and clips (x2) that attach the inductive charger to the phone dock.
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide the inductive charger datums into the phone dock, and then fully engage the tabs at the top of the phone dock.
  2. Install the screws (x3) that attach the inductive charger to the phone dock.
    1 Nm (.7 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 bit
    • Ratchet/torque wrench
  3. Fasten the clips (x2), screw gaskets (x2), and guide tabs (x6) that attach the phone dock to the center console.
    Informational PurposesAn informational icon, calling your attention
    Note
    Press the phone dock from the bottom up to the inside along the tilt angle of the phone dock assembly.
  4. Connect the electrical connector, and then install the phone dock to the instrument panel.
  5. Install the screws (x2) that attach the phone dock to the center console assembly.
    1.2 Nm (.9 lbs-ft)
    Tip: Use of the following tool(s) is recommended:
    • Torx T20 bit
    • 2 in extension
    • Ratchet/torque wrench
  6. Install the center console. See Center Console (Remove and Replace).