Brake Caliper - Rear (Sport Brakes) - LH (Remove and Replace)
Correction code 3301020032 FRT 0.54 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.
- 2024-09-17: Added EPB Service Mode reference
Torque Specifications
Bolt that attaches the LH rear EPB harness bracket to the LH rear caliper |
|
|
Reuse | |
Bolt that attaches the LH rear brake hose to the brake caliper |
|
|
Reuse | |
Nut at the jounce hose bracket |
|
|
Reuse | |
Bolts (x2) that attach the LH rear caliper bracket to the knuckle |
|
|
Replace | Bolts: 1188643-00-C |
Remove
- Raise and support the vehicle. See GUID-0ECF2493-88F6-48E9-ADBB-9AE1D52E217C.html.
- Open the LH front door and lower the LH front window.
- Place the vehicle into EPB Service Mode. See Parking Brake - Caliper - Rear - LH (Release).
- Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
- Remove LH rear wheel. See Wheel Assembly (Remove and Install).
- Disconnect the LH rear EPB caliper connector.
-
Remove the bolt that attaches the LH
rear EPB harness bracket to the LH rear caliper.
Tip: Use of the following tool(s) is recommended:
- 4 in extension
- Ratchet/torque wrench
- 10 mm socket
- Position the oil drain under the rear LH brake hose.
-
Remove the bolt that attaches the LH
rear brake hose to the brake caliper.
NoteThe bolt and washers (x2) are captive and cannot be reused. Replace the hose assembly if the bolt is loosened or removed.Tip: Use of the following tool(s) is recommended:
- Ratchet/torque wrench
- 11 mm 12-point deep socket
-
Remove the brake line tube nut from
the brake hose at the jounce hose bracket. Allow the fluid to drain.
Tip: Use of the following tool(s) is recommended:
- 3 in extension
- Ratchet/torque wrench
- 12 mm socket
- Release and discard the clip that attaches the brake hose to the jounce hose bracket, and then remove the hose from the bracket.
-
Remove and discard the bolts (x2) that
attach the LH rear caliper bracket to the knuckle, and then remove the caliper from the
vehicle.
NoteUse of the following tool(s) is recommended:
- Cordless Ratchet/Impact Driver
- 3 in extension
- External Torx E18
- Ratchet/torque wrench
Install
-
Install the LH rear brake caliper onto
the LH rear knuckle, and then install new bolts to attach the caliper to the
knuckle.Tip: Use of the following tool(s) is recommended:
- Cordless Ratchet/Impact Driver
- 3 in extension
- External Torx E18
- Ratchet/torque wrench
-
Install the bolt that attaches a new
hose to the LH rear brake caliper. NoteThe bolt and washers are captive in the new hose assembly.Tip: Use of the following tool(s) is recommended:
- Ratchet/torque wrench
- 11 mm 12-point deep socket
-
Install the hose into the jounce hose bracket, and then install a new clip that
attaches the brake hose to the jounce hose bracket.
NotePay attention to the clip orientation.
-
Install the brake line tube nut to
the brake hose at the jounce hose bracket.
Tip: Use of the following tool(s) is recommended:
- 3 in extension
- Ratchet/torque wrench
- 12 mm socket
-
Install the bolt that attaches the LH
rear EPB harness bracket to the LH rear caliper.
Tip: Use of the following tool(s) is recommended:
- 4 in extension
- Ratchet/torque wrench
- 10 mm socket
- Connect the LH rear EPB caliper connector.
- Remove the oil drain from under the vehicle.
- Perform a brake fluid flush on the LH rear brake. See Brake Fluid Bleed/Flush (Maintenance).