Brake Fluid
Brake Fluid Hydraulan 406® ESI
| Test Item |
Test Method |
Typical Properties |
| pH value |
|
7.7 (50% (m)) |
| Solidification temperature |
DIN 51583 |
< -50°C |
| Boiling temperaqture |
ASTM D1120 |
271°C (1,013 hPa) |
| Flash point |
ISO 2719 |
137.5°C |
| Flammability |
Derived from Flash point |
Hardly combustible |
| Lower explosion limit |
DIN 51649-1 |
For liquids not relevant for
classification and labelling. The lower explosion point may be 5 -
15°C below the flash point |
| Upper explosion limit |
DIN 51649-1 |
For liquids not relevant for
classification and labelling. |
| Ignition temperature |
DIN EN ISO/IEC 80079-20-1 |
222°C |
| DIN 51794 |
230°C |
| Vapour pressure |
|
1 hPa (50°C) |
|
1 hPa (20°C) |
| Density |
DIN 51757 |
1.06 g/cm3 (20°C) |
| Relative vapour desity (air) |
|
>1 (20°C) |
| Solubility in water |
|
Soluble |
| Self ignition |
|
Not self-igniting |
| Thermal decomposition |
|
No decomposition if used as
directed |
| Viscosity, dynamic |
ASTM D445 |
7.2 mPa.s (40°C) |
| Viscosity, kinematic |
ASTM D445 |
11.5 mm2/s (23°C) |
| ASTM D445 |
6.8 mm2/s (40°C) |
| Explosion hazard |
|
Not explosive |
| Fire promoting properties |
|
Not fire-propagating |
| Hygroscopy |
|
hygroscopic |
Coolant G48
Ingredients: Ethyleneglycol (>90%), 2-ethylhexanoic acid, sodium salt (2% - 3%)
| Test Item |
Test Method |
Typical Properties |
| Solidification temperature |
DIN/ISO 3016 |
< -18°C |
| Boiling point |
ASTM D1120 |
≥ 165°C |
| Flash point |
DIN/EN 22719; ISO 2719 |
126.5°C |
| Lower explosion limit |
|
4.9% (V) |
| Upper explosion limit |
|
14.6% (V) |
| Ignition temperature |
DIN 51794 |
440°C |
| Vapour pressure |
|
0.2 hPa (20°C) |
| Density |
DIN 51757 |
approx. 1.12 g/cm3 (20°C) |
| Miscibility with water |
|
Miscible in all
proportions |
| Hygroscopy |
|
Hygroscopic |
| Viscosity, kinematic |
DIN 51562 |
20 - 30 mm2/s (20°C) |
Drive Unit Lubricant KAF 1 (V1.2)
KAF 1 (V1.2) is Tesla High
Performance Passenger Vehicle Fluid as a replacement of current KAF1 (1646886-XX-A)
and EDF2 (1616951-XX-A) for all Passenger Vehicle Drive Unit Lubricants.
| Test Item |
Test Method |
Typical Properties |
Requirements |
| ASTM color |
ASTM D1500 |
Amber |
Amber |
| Appearance |
Visual |
Bright and Clear |
Bright and Clear |
| Density @ 15°C |
ASTM 4052 |
0.837 |
- |
| Kinematic Viscosity @ 100°C,
CsT |
ASTM D445 |
6.3 |
5.8 - 6.7 |
| Kinematic Viscosity @ 40°C,
CsT |
ASTM D445 |
29 |
28 - 31 |
| Viscosity Index |
ASTM D2270 |
178 |
Min. 160 |
| Flash Point, COC, °C |
ASTM D92 |
220 |
Min. 200 |
| Pour Point, °C |
ASTM D97 |
-40 |
Max. -36 |
| Brookfield Viscosity @ -20°C,
cP |
ASTM D2983 |
790 |
Max. 880 |
| Foam, tend./stab |
ASTM D892 |
10/0 (Seq-I) |
Max. 50/0 |
| Foam, tend./stab |
ASTM D892 |
20/0 (Seq-II) |
Max. 50/0 |
| Foam, tend./stab |
ASTM D892 |
10/0 (Seq-III) |
Max. 50/0 |
| Copper Corrosion, 3hr @
150°C |
ASTM D130 |
3b |
< 4a |
| Sulfur, ppm |
ASTM D6443 |
1,856 |
- |
| Phosphorus, ppm |
ASTM D5185 |
261 |
- |
| Calcium, ppm |
ASTM D5185 |
122 |
- |
| Boron, ppm |
ASTM D5185 |
73 |
- |
| Chlorine |
ASTM D5185 |
- |
- |
| ISO Cleanliness Code |
ISO 4406 (≥ 4 µm, ≥ 6 µm, and ≥ 14
µm ) |
Report/17/14 |
Max. report/17/14 |
Windshield Washer Fluid
Ingredients: Ethanol, Isopropyl alcohol
| Component/Test Item |
Control parameter/Permissible
concentration |
| Ethanol |
1,000 ppm, 1900 mg/m3 |
| Isopropyl alcohol |
500 ppm, 1,225 mg/m3 |
| Appearance |
Liquid |
| Color |
Blue |
| Flash point |
27°C |
| Relative density |
0.9 (20°C) |
| Density |
0.8992 g/cm3 (20°C) |