2026-08-09

Valance - Front Fascia (Remove and Replace)

Correction code 1203010052 FRT 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2026-07-31: Added steps for the super horn cover clip.
  • 2026-03-16: Added notes and tools for bolts securing front valance to front fascia on newer vehicles.
Informational PurposesAn informational icon, calling your attention
Note
The images in this repair procedure show a Non-Performance vehicle. The instructions apply to both the Non-Performance and the Performance version.

Torque Specifications

Table 1. Torque Specifications: Valance - Front Fascia (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Screws (x3) that attach the super horn to the valance
1.8 Nm (1.3 lbs-ft)
  • Torx T25 socket
 Reuse
Bolts (x8) that attach the valance to the fascia
3 Nm (2.2 lbs-ft)
  • Torx T40 socket
  • (If equipped) 10 mm socket
 Reuse
Nuts (x2) at the LH and RH corners of the valance
3 Nm (2.2 lbs-ft)
  • 10 mm socket
 Reuse

Remove

  1. Remove the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  2. Remove the push clips (x6) that attach the LH and RH sides of the valance to the wheel arch liners.
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove the outer clips as necessary to allow for easier access to the nuts behind the wheel liner.
  3. Remove the clip that attaches the super horn cover to the front fascia.
  4. Remove the nuts (x2) at the LH and RH corners of the valance.
    Informational PurposesAn informational icon, calling your attention
    Note
    The nuts are accessed from behind the front of the wheel arch liners.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  5. Release the clip that attaches the super horn harness to the super horn, and then disconnect the super horn connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    The connector access may vary depending on the version of the super horn audio speaker installed on the vehicle.
  6. Remove the bolts (x8) that attach the valance to the front fascia, and then remove the valance from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Newer vehicles are equipped with 6 T40 bolts and 2 10mm bolts.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T40 socket
    • (If equipped) 10 mm socket
  7. Remove the screws (x3) that attach the super horn to the valance, and then remove the super horn from the valance.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 socket

Install

  1. Install the super horn to the valance, and then install the screws (x3) that attach the super horn to the valance.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 socket
  2. Install the valance to the front fascia, and install the bolts (x8) that attach the valance to the fascia.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Newer vehicles are equipped with 6 T40 bolts and 2 10mm bolts.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T40 socket
    • (If equipped) 10 mm socket
  3. Connect the super horn connector, and then install the clip that attaches the super horn harness to the super horn.
  4. Install the nuts (x2) at the LH and RH corners of the valance.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    The nuts are accessed from behind the front of the wheel liners.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  5. Install the clip that attaches the super horn cover to the front fascia.
  6. Install the push clips (x6) that attach the LH and RH sides of the valance to the wheel liners.
  7. Install the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).