30/10/2024 22:41:12

Check Valve - Evaporator (Remove and Replace)

Correction code 1840011222 FRT 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Personal Protection to make sure wearing proper PPE when performing the below procedure.

  • 2024-02-05: Remove the ""Stop Thermal Fill Drain" routine.
Informational PurposesAn informational icon, calling your attention
Note
This procedure requires the A/C Refrigerant (Recovery and Recharge) procedure to be performed. If not already automatically added to the Service Visit, add correction code 18200102 as a separate activity to the Service Visit.

Remove

  1. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  2. Enable Service Mode via vehicle touchscreen. See Service Mode.
  3. Unlock the vehicle gateway. See Gateway Unlock.
  4. On the touchscreen, touch Service Mode > Thermal > Refrigerant System > Start Thermal Fill Drain (Refrigerant Only) and select Run to start the "Start Thermal Fill Drain (Refrigerant Only)" routine.
  5. Recover the A/C refrigerant. See A/C Refrigerant (Recovery and Recharge) (Maintenance).
  6. Remove and discard the evaporator check valve snap ring from the supermanifold.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  7. Remove the evaporator check valve from the supermanifold.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    If the check valve separates from the aluminum cap during removal, do not use metal tools. Metal tools may scrape the supermanifold housing causing internal damage. Use fingers or wrap electrical tape around a 90 degree pick instead.

Install

  1. Lubricate O-rings with the appropriate A/C oil. See Fluids and Capacities for A/C oil specifications. Then install the check valve into the supermanifold.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  2. Install a new evaporator check valve snap ring onto the supermanifold.
    Informational PurposesAn informational icon, calling your attention
    Note
    Verify the snap ring is properly seated inside the groove on the supermanifold.
  3. Perform the vacuum leak test and oil injection. See Vacuum Leak Test and Oil Injection.
  4. Recharge the A/C refrigerant. See A/C Refrigerant (Recovery and Recharge) (Maintenance).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Recharge the refrigerant exactly as instructed. Failure to adhere to the instructions can cause catastrophic damage to the cooling system.
  5. Remove the AC hoses from the vehicle.
  6. Install caps onto the AC ports.
  7. If a refrigerant leak detector is available, make sure that there is no leak at the low pressure temperature sensor.
  8. Access the thermal system routines on the touchscreen: Touch Quick Controls > Service Mode > Diagnostics > Thermal.
  9. Perform the heat pump commissioning through UI: Touch Thermal > Sensors and Valves > Run Heat Pump Commissioning and then touch Run.
    Informational PurposesAn informational icon, calling your attention
    Note
    Touch Close once the routine is passed.
  10. Perform the thermal performance test through UI: Touch Thermal > Actions > Test Thermal Performance and then touch Run.
    Informational PurposesAn informational icon, calling your attention
    Note
    Touch Close once the routine is passed.
  11. Perform the HVAC performance test through UI: Touch Thermal > Actions > Test HVAC Performance and then touch Run.
    Informational PurposesAn informational icon, calling your attention
    Note
    Touch Close once the routine is passed.
  12. Exit Service Mode through UI. See Service Mode.
  13. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).