Week Ending September 28, 2024

The following procedure(s) were updated:

1. Alignment Requirement - Suspension - Added instruction to perform an alignment check when servicing the RH rear upper fore link.

Week Ending September 21, 2024

The following procedure(s) were updated:

1. How to Use this Manual - Added information on the crowsfoot/offset wrench extension calculator.
2. Receiver Dryer and Desiccant (Non-Heat Pump) (Remove and Replace) - Added note on adding correction code for refrigerant recovery/recharge 18200102 as a separate activity to the service visit.
3. Supermanifold (Remove and Replace) - Added note on adding correction code for refrigerant recovery/recharge 18200102 as a separate activity to the service visit.

Week Ending September 14, 2024

The following procedure(s) were updated:

1. A/C Line - Supermanifold to HVAC (Remove and Replace) - Added note on adding correction code for refrigerant - recovery/recharge as a separate activity to the Service Visit.
2. Antenna - GPS (Remove and Replace) - Added note that it is unnecessary to disconnect the harness from triple camera assembly.
3. Car Computer (Remove and Replace) - Added owner authorization request and LV maintainer steps.
4. Connectivity Board - Car Computer (Info-Ryzen) (Remove and Replace) - Added steps according to the latest validation.
5. Desiccant (Heat Pump) (Remove and Replace) - Added warnings to wear suitable protective clothing, consisting of face and eye protection, heat-proof gloves, rubber boots and apron or waterproof overalls must be worn when carrying out operations on the air conditioning system.
6. All HV Battery (Remove and Replace) procedures - Added step to support the LV system.
7. Receiver Dryer and Desiccant (Non-Heat Pump) (Remove and Replace) - Added warnings to wear suitable protective clothing, consisting of face and eye protection, heat-proof gloves, rubber boots and apron or waterproof overalls must be worn when carrying out operations on the air conditioning system.
8. TPMS (Sensor ID Tool Learn) - Added note with links to update TPMS Tool firmware.

Week Ending September 7, 2024

The following procedure(s) were updated:

1. HV Battery (RWD) (Remove and Replace) - Added "High Voltage Awareness" certification warning.

Week Ending August 31, 2024

The following procedure(s) were updated:

1. Alignment Requirement - Suspension - Added instruction on proper consumption of alignment adjustment correction codes.
2. Clear Forward Camera View (Precision Cleaning Of Inboard Windshield) - Added a step to clean the wiper blades.
3. Desiccant (Heat Pump) (Remove and Replace) - Added note on adding correction code for refrigerant recovery/recharge 18200102 as a separate activity to the service visit, added special tools for accumulator cap removal.
4. Tesla Badge - Rear (Remove and Replace) - Added a note to remind that the rear badge is not reusable due to the positioning problem.

Week Ending August 24, 2024

The following new procedure(s) were added:

1. AC Cable - Charge Port to HV Battery (3-Phase) (Retrofit)
2. Wheel Disposal (Rework)

The following procedure(s) were updated:

1. Harness - Ancillary Bay - HV Battery (Remove and Replace) - Added note for newer harness version.
2. Oil Pump - Rear Drive Unit (3DU) (Remove and Replace) - Added instruction to perform software reinstall before running oil pump-related Toolbox routines.
3. Radiator (Heat Pump) (Remove and Replace) - Updated linked to procedure to Cooling Fan Module to correct missing steps.
4. Superbottle (Dual Motor) (Remove and Replace) - Added O-ring part numbers 1111740-00-A and 1111737-00-A for the suction/liquid line fitting.
5. Wheel (Remove and Replace) - Added instruction on wheel disposal.

Week Ending August 17, 2024

The following new procedure(s) were added:

1. Car Computer (Remove and Replace) - Car Computer replacement procedure that uses Toolbox to associate the replacement computer. Please send us feedback on this procedure!
2. LV Battery - Recover (Heat Pump) - Please send us feedback on this procedure!

Week Ending August 10, 2024

The following new procedure(s) were added:

1. Vehicle Sanitation - Evaporator - Models with PTC Heater - Tunap 994 (EMEA)

The following procedure(s) were updated:

1. Coolant Pump - HV Battery (Remove and Replace) - Changed instruction for lubrication of O-rings to use Silicone lubricant instead of using silaramic grease.
2. Coolant Pump - Powertrain (Remove and Replace) - Changed instruction for lubrication of O-rings to use Silicone lubricant instead of using silaramic grease.
3. Coolant Pump - Powertrain (Heat Pump) (Remove and Replace) - Changed instruction for lubrication of O-rings to use Silicone lubricant instead of using silaramic grease.
4. Door and Hinge Cover - Charge Port (Remove and Replace) - Removed unnecessary step.
5. NVH Tape - Brake Pads - Rear (EMEA) (Retrofit) - Updated instructions to apply tape only on inner brake pads.
6. Vehicle Sanitation - Evaporator - Tunap 994 (EMEA) - Removed procedures using Tunap 996 and Tunap I5880 from original procedure.
7. Vehicle Sanitation - Interior Air - Tunap 589 (EMEA) - Modified procedure for use of Tunap 589 only.

Week Ending August 3, 2024

The following procedure(s) were updated:

1. GUID-75F5DDAF-3D00-474E-9D0A-CB1A1B3324A1.html - Added information on installing a recycling warning label with CE marking and manufacturer information, if this was present on the ancillary bay cover being replaced.
2. Cover - Ancillary Bay (Remove and Replace) -
3. IP Carrier (LHD) (Remove and Replace) - Added information about how to handle the replacement between different versions of IP carrier.
4. Power Trunk (Remove and Replace) - Added trunk harness ground strap discarded fasteners part number 1508949-00-A.

Week Ending July 27, 2024

The following procedure(s) were updated:

1. Cover - Ancillary Bay (Structural Pack) (3-Phase) (Remove and Replace) - Added information on installing a recycling warning label with CE marking and manufacturer information, if this was present on the ancillary bay cover being replaced.
2. Fuse Locations - Update the link of Electrical Information.
3. Seat Back - 2nd Row - LH (Remove and Replace) - Deleted the 2nd row seat buckle steps.
4. Toolbox 3 (Connect and Disconnect) - Added warning for OBD-II to RJ45 Ethernet diagnostic equipment.

Week Ending July 20, 2024

The following procedure(s) were updated:

1. Controller - High Voltage (Backup and Restore) - Introduced Service Mode Plus activation using the Vehicle Ops App, updated touchscreen images for backing up and restoring backup data.
2. Module - Body Controller - Security (Remove and Replace) - Updated the way of performing the routines from using Toolbox to using the touchscreen.
3. NVH Tape - Brake Pads - Front (EMEA) (Retrofit) - Updated procedure for pre-cut stickers and added region information.
4. NVH Tape - Brake Pads - Rear (EMEA) (Retrofit) - Updated procedure for pre-cut stickers and added region information.

Week Ending July 13, 2024

The following procedure(s) were updated:

1. A/C Compressor, Supermanifold and A/C Lines (Heat Pump) (Remove & Replace) - Added details to identify the type of A/C line to be used in "refrigACLineType" configuration.

Week Ending July 6, 2024

The following procedure(s) were updated:

1. Ancillary Bay Coolant (Drain and Refill) - Added caution for hose reconnection.
2. Brake Fluid Bleed - One Caliper - Corrected torque figures for brake caliper bleed valves.
3. Brake Lines - Rear - RH to Sill (Remove and Replace) - Changed last step to perform alignment check/adjust to reference to alignment requirement table.
4. Clear Forward Camera View (Precision Cleaning Of Inboard Windshield) - Updated tool part numbers.
5. Mount - Front Drive Unit - LH (Remove and Replace) - Changed last step to perform alignment check/adjust to reference to alignment requirement table.