Current Release Notes

Archived Release Notes:

Week Ending December 21, 2024

The following procedure(s) were updated:
  1. Hose - Outlet - Rear Drive Unit (3DU) (Remove and Replace) - Updated entire procedure to latest validation.
  2. HV Battery (AWD) (Remove and Replace):
    • Added a step to verify the front HV battery coolant passthrough fittings on the new HV battery to determine if the updated front HV battery coolant manifold hose 1734606-00-D is needed.
    • Added step to determine if HV battery parameters are within safe limits before removing the pyro disconnect.
  3. HV Battery (RWD) (Remove and Replace):
    • Added a step to verify the front HV battery coolant passthrough fittings on the new HV battery to determine if the updated front HV battery coolant manifold hose 1734606-00-D is needed.
    • Added step to determine if HV battery parameters are within safe limits before removing the pyro disconnect.
  4. Sensor - Radar - Front (Calibration) - Added a note for EMEA. If the conditions are met, this procedure is not required.

Week Ending December 14, 2024

The following new procedure(s) were added:
  1. New glass components (windshield, roof, door, and fixed glass) must be inspected before installation to meet Tesla’s internal standards of quality. The Pre-Installation Glass Inspection procedure explains how to inspect new windshield, roof, door, and fixed glass components before the new component is installed.
The following procedure(s) were updated:
  1. Added a new caution about Pre-Installation Glass Inspection service requirements:
  2. Four Wheel Alignment Check and Adjust - Removed instruction to add the test drive correction code. The test drive is now included in the alignment FRT.
  3. Frame - Seat Cushion - Driver Seat (Remove and Replace) - Added mini-tilt motor configuration information.
  4. Frame - Seat Cushion - Front Passenger Seat (Remove and Replace) - Added mini-tilt motor configuration information.
  5. Knuckle - Suspension - Rear - LH (Remove and Replace) - Made correction to Note that mentions one/both rear lower fore links.
  6. Motor - Seat Tilt - Driver Seat (Remove and Replace) - Added mini-tilt motor configuration information.
  7. Seatbelt - 2nd Row - LH (Remove and Replace) - Fixed incorrect torque values for retractor to body fastener.
  8. Sensor - TPMS (Remove and Replace) - Remove the step of programming the TPMS sensor ID.

Week Ending December 7, 2024

The following procedure(s) were updated:
  1. Updated inverter fastener torque sequence.
  2. Seat Assembly - 1st Row - LH (Remove and Replace) - Added configuration information for front seat assemblies with the Tesla mini-tilt motor.
  3. Sensor - Relative Humidity and Temperature (Remove and Replace) - Updated notes and Service Mode instructions.
  4. Steering Column (RHD) (Remove and Replace) - Modified steering column configuration and calibration steps.
  5. TPMS (Sensor ID Tool Learn) - Updated Service Mode instructions.

Week Ending November 30, 2024

The following procedure(s) were updated:
  1. Cooling System (Vacuum Refill) - Added images of vacuum refill tool setup and added warning on incorrect use of the refill tool.
  2. Hose - Front Manifold - LH (Remove and Replace) - Add some steps when replacing with the new hose.
  3. Isolator - Motor Mount - Front - LH (Remove and Replace) - Added note on o-ring installation.
  4. Supermanifold (Remove and Replace) - Added information on manually configuring replacement coolant pumps (optional).

Week Ending November 23, 2024

The following procedure(s) were updated:
  1. 12V/LV Battery (Remove and Replace) - Added a note to remind of checking the 12V/LV battery temperature before performing the procedure.

Week Ending November 9, 2024

The following procedure(s) were updated:
  1. GUID-80085B62-8460-4B8A-8B4F-31FD723E5593.html - Modified last step to instruct to add correction code for brake burnishing as a separate activity to the Service Visit.
  2. Camera - Interior (Remove and Replace) - Added note that Service Mode must be enabled prior to connecting the replacement camera.
  3. Compressor (Non-Heat Pump) (Remove and Replace) - Corrected torque figure for the bolt that attaches the fitting to the chiller and EXV assembly.
  4. HV Battery (AWD) (Remove and Replace) - Updated HV battery discharge steps.
  5. HV Battery (RWD) (Remove and Replace) - Updated HV battery discharge steps.

Week Ending November 2, 2024

The following new procedure(s) were added:
  1. Windshield Chip Repair (EMEA)
The following procedure(s) were updated:
  1. Alignment Requirement - Suspension - Removed alignment check from rear upper fore link, as a new service procedure for the link, which does not release the rear subframe, has been validated.
  2. Steering Column (LHD) (Remove and Replace) - Added step to transfer clip from old column to new column.
  3. Steering Column (RHD) (Remove and Replace) - Added step to transfer clip from old column to new column.

Week Ending October 26, 2024

The following new procedure(s) were added:
  1. Horn - High Tone (Remove and Replace) (Heat Pump)
  2. Horn - Low Tone (Remove and Replace) (LV Battery)
The following procedure(s) were updated:
  1. Clear Forward Camera View (Precision Cleaning Of Inboard Windshield) - Added a video demonstrating precision cleaning of windshield.
  2. Trunk (Remove and Replace) - Added a reminder for technicians to install all badges that are equipped with the working vehicle.
  3. Vehicle HV Disablement Procedure - Rearranged multimeter probing images to align with HV measurement table.

Week Ending October 19, 2024

The following new procedure(s) were added:
  1. Car Computer (Dispose)
The following procedure(s) were updated:
  1. Car Computer (Remove and Replace) - Added instruction for car computer disposal.
  2. Motor - Seat Track - Front Passenger Seat (Remove and Replace) - Updated post-installation routines.
  3. Subframe Assembly - Rear (Remove and Install) - Updated torque spec for LH/RH shear plate-to-rear subframe large bolts.

Week Ending October 12, 2024

The following new procedure(s) were added:
  1. Event Data Recorder Retrieval
The following procedure(s) were updated:
  1. Motor - Brake Caliper - Rear - LH (Remove and Replace) - Remove road test after installation.
  2. Pyrotechnic Battery Disconnect (Remove and Replace) - Updated figure in step 7 to display proper PPE.