19/08/2022 09:57:36

Actuator - Track Release - Easy Entry - 2nd Row - LH (Remove and Replace)

Correction code 13026502

Warning

This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

Open LH front door
Using MCU, open all doors, liftgate and hood
Move LH front seat forward
Move RH front seat forward
Open hood

Note
Using MCU touchscreen > Controls > Frunk Trunk
Remove underhood aprons

Note
4x aprons
Remove frunk carpet

Note
2x connector
Remove underhood storage unit

Note
10x bolts, 10mm, 4 Nm, 10x bolts, 10mm, 7 Nm
Remove HEPA filter

Note
Lift up from bottom and pull out
Remove 2nd row floor mat
Remove LH welcome plate

Note
8x clips
Remove LH rear door sill

Note
1x patch bolt, T25, 2.5 Nm, 2x clips, Discard after removal
Move 60 seat fully forward using easy entry
Tape the LH lower C-pillar area around the 2nd row seat side trim area
Apply tape to LH racetrack to avoid damage
Remove front screw securing LH lower C-pillar

Note
1x patch screw, T25, 2.5 Nm, Discard after removal
Fold down LH 3rd row seat

Note
Press button located on LH 3rd row seat back assembly near headrest, fold seat back down towards front of vehicle into a flat position
Fold down RH 3rd row seat

Note
Press button located on RH 3rd row seat back assembly near headrest, fold seat back down towards front of vehicle into a flat position
Remove LH trunk sill side trim

Note
4x clips
Remove screw securing LH C-pillar mid trim

Note
1x screw, T20, 2 Nm
Release clips securing LH C-pillar mid trim and remove

Note
9x clips
Remove screws securing C-pillar lower panel to LH parcel shelf support

Note
2x screws, T20, 2 Nm
Release clips securing rear edge of LH C-pillar lower panel to rear trunk side carpet panel and pull top edge of C-pillar lower panel out

Note
2x clips, 1x magnet
Release clips securing LH C-pillar lower panel along front edge and remove panel

Note
9x clips, 1x magnet
Remove RH trunk sill side trim

Note
4x clips
Remove screw securing RH C-pillar mid trim

Note
1x screw, T20, 2 Nm
Release clips securing RH C-pillar mid trim and remove

Note
9x clips
Remove fasteners securing C-pillar lower panel to RH parcel shelf support

Note
2x screws, T20, 2 Nm
Remove RH welcome plate

Note
8x clips
Remove front screw securing RH lower C-pillar

Note
1x screw, T25, 2.5 Nm, Discard after removal
Remove RH rear door sill trim

Note
1x patch bolt, T25, 2.5 Nm, 2x clips, Discard bolt after removal
Move 40 seat fully forward using easy entry
Tape the RH lower C-pillar area around the 2nd row seat side trim area
Apply tape to the RH racetrack to avoid damage
Release clips securing RH C-pillar lower panel along front edge and remove panel

Note
9x clips, 1x magnet
Move 40 seat back and out of easy entry position
Move 60 seat back and out of easy entry position
Tape rear center console cup holder trim to prevent from damage
Remove 2nd row floor panel 2

Note
6x clips, Replace any broken clips, Lift the front of panel toward the rear of the vehicle, then pull the floor panel out
Move 60 seat fully forward using easy entry
Move 40 seat fully forward using easy entry
Remove 2nd row floor panel 3

Note
Lift front of panel up to release clips, While lifting up, need to release the rear sliding plates from the seat and slide them all the way back, Once free, lift rear of panel and slide out from behind seats, Use caution since floor panel can damage HVAC ducts
Move 60 seat fully backwards

Note
Using easy entry unlatch seat and move it fully backwards, Create space to inspect under seat, Latch seatback to lock into position
Power down vehicle using MCU

Note
Via Controls > Safety & Security > ''Power off''
Disconnect 12V negative terminal and First Responder Loop

Note
1x nut, 10mm, 5 Nm, 1x connector, Wait at least 2 minutes before disconnecting modules or HV components
Remove LH bench seat floor support
Remove center bench seat floor support
Disconnect 60 seat harness

Note
2x connectors, Release bracket for better access
Release harness from LH floor support bracket

Note
2x clips
Remove LH outer sliding closeout panel

Note
1x clip, Need to peel sticker back to release clip
Remove LH inner sliding closeout panel

Note
1x clip, Need to peel sticker back to release clip
Remove fasteners securing the 60 bench

Note
12x bolts, 11mm, 45 Nm
Fold down 60 seat
Remove 60 seat assembly from vehicle

Note
Recommend assistance
Unfold the 60 seat assembly
Release rear toe kick from 60 seat assembly

Note
6x J-hooks, Release lower outer two to expose inner 4 clips
Remove center seat belt buckle from seat

Note
1x patch bolt, T50, 45 Nm, Discard after removal, 1x connector, 1x edge clip
Remove 60 seat assembly release handle

Note
Pry at pivot point to release
Remove LH outer recliner cover

Note
1x bolt, 10mm, 6 Nm, 1x push clip, 4x clips
Remove LH outer seat belt from the 60 seat assembly

Note
1x patch bolt, T50, 45 Nm, Discard after removal
Release upholstery from under side of 60 seat assembly

Note
11x J-hooks
Disconnect seat cushion connectors

Note
2x gray connectors, 2x black connectors, Black connectors must be released from seat frame
Remove lower seat cushion from LH 60 seat assembly

Note
Use caution feeding J-hooks and connectors through seat frame
Remove RH fasteners securing the inner riser cover

Note
2x screw bottom, T20, 2 Nm, 1x screw top, T20, 4 Nm
Remove RH fasteners securing the outer riser cover

Note
1x screw, T20, 4 Nm
Remove RH riser cover from seat

Note
2x clips
Remove LH fasteners securing the outer riser cover

Note
2x screw bottom, T20, 2 Nm, 1x screw top, T20, 4 Nm
Remove LH fasteners securing the inner riser cover

Note
1x screw, T20, 4 Nm
Remove RH riser cover from seat

Note
2x clips
Remove screw securing splitter box to 60 seat assembly

Note
1x screw, T20, 1.5 Nm
Remove screw securing splitter box spring to 60 seat assembly

Note
2x screws, T20, 1.5 Nm
Remove the front cushion support

Note
5x bolts, 10mm, 6 Nm
Release cable from the LH track

Note
1x cable, cable is secured in bracket at to points
Release cable from the RH track

Note
1x cable, cable is secured in bracket at to points
Release both cables from cable clips

Note
3x cable clips, Leave the clip in the seat frame, release the cable from the clip only
Remove the bolt securing actuator assembly to seat frame

Note
1x bolt, 10mm, 6 Nm
Remove actuator assembly from seat frame

Note
1x cable, turn 30 degrees to right and push back to remove from seat frame
Remove actuator assembly from seat assembly

Note
1x cable, Remove actuator cable from actuator assembly
Position and install actuator assembly to actuator

Note
1x cable, Do not remove the black pin before the actuator assembly cable is attached to the actuator
Install actuator assembly onto seat frame

Note
Attach actuator assembly onto back tab then move forward and turn 30 degrees to latch on the second tab
Install the bolt securing actuator assembly to seat frame

Note
1x bolt, 10mm, 6 Nm
Connect the RH side cable to the track

Note
2x cable bracket
Connect the LH side cable to the track

Note
2x cable bracket
Install both cables to cable clips

Note
3x cable clips
Install bolts securing the front cushion support

Note
6x bolts, 10mm, 6 Nm
Install screw securing splitter box to 60 seat assembly

Note
1x screw, T20, 1.5 Nm
Install screw securing splitter box spring to 60 seat assembly

Note
2x screw, T20, 1.5 Nm
Install RH riser cover onto the seat

Note
Make sure to secure the clips
Install the LH outer fasteners

Note
2x screw bottom, T20, 2 Nm, 1x screw top, T20, 4 Nm
Install the LH inner fasteners

Note
3x screw, T20, 4 Nm
Install RH riser cover onto the seat

Note
Make sure to secure the clips
Install the RH inner fasteners

Note
1x screw, T20, 4 Nm
Install the RH outer fasteners

Note
2x screw bottom, T20, 2 Nm, 1x screw top, T20, 4 Nm
Install cushion onto the seat

Note
Use caution feeding J-hooks and connectors through seat frame
Connect seat cushion connectors

Note
2x gray connectors, 2x black connectors, Secure black connectors to seat frame
Secure upholstery to under side of 60 seat assembly

Note
11x J-hooks, Position cushion onto seat frame and then fold seat back down for better access, Fold seat back up once complete
Install LH outer seat belt to the 60 seat assembly

Note
1x patch bolt, T50, 45 Nm, Install new patch bolt
Install LH outer recliner cover

Note
1x bolt, 10mm, 6 Nm, 1x push clip, 4x clips
Install 60 seat assembly release handle

Note
1x spring clip
Install LH center seat belt buckle onto seat

Note
1x patch bolt, T50, 45 Nm, Install new patch bolt, 1x connector, 1x edge clip
Secure toe kick to 60 seat assembly

Note
6x J-hooks, Secure inner 4 clips, then lower outer 2
Fold 60 seat back down
Install 60 seat assembly into vehicle

Note
Recommend assistance, Make sure guide pins are aligned properly
Unfold the 60 seat assembly
Install forward most 60 seat track bolts hand tight

Note
2x bolts, 11mm, 45 Nm
Secure 60 seat harness to LH floor support bracket

Note
2x clips
Connect 60 seat assembly harness

Note
2x connectors, Secure connector housing to bracket
Connect first responder loop and then 12V negative terminal

Note
1x connector, 1x nut, 10mm, 5 Nm
Move 60 seat fully forward using easy entry
Install rear center 60 seat track bolts

Note
2x bolts, 11mm, 45 Nm
Install remaining rear 60 seat track bolts

Note
4x bolts, 11mm, 45 Nm
Move 60 seat back and out of easy entry position
Torque forward most 60 seat track bolts

Note
2x bolts, 11mm, 45 Nm
Install remaining front 60 seat track bolts

Note
4x bolts, 11mm, 45 Nm
Install center bench seat floor support
Install LH bench seat floor support
Install LH inner sliding closeout panel

Note
1x clip, Need to lay sticker back down to cover the fastener
Install LH outer sliding closeout panel

Note
1x clip, Need to lay sticker back down to cover the fastener
Move 40 seat fully forward using easy entry
Move 60 seat fully forward using easy entry
Install 2nd row floor panel 3

Note
2x clips, Use caution near HVAC ducts
Move 60 seat back and out of easy entry position

Note
Moving seat fully rearward will secure sliding plates to seat
Move 40 seat back and out of easy entry position

Note
Moving seat fully rearward will secure sliding plates to seat
Install 2nd row floor panel 2

Note
6x clips, Replace clips if damaged, Install rear of panel into position and then secure clips
Remove tape from rear center console trim
Move 40 seat fully forward using easy entry
Move 60 seat fully forward using easy entry
Install RH C-pillar lower panel and secure clips along front edge

Note
9x clips, 1x magnet
Install screw securing front of RH lower C-pillar

Note
1x patch screw, T25, 2.5 Nm, Install new screw
Install RH rear door sill trim

Note
1x patch bolt, T25, 2.5 Nm, 2x clips, Install new patch bolt
Install RH welcome plate

Note
8x clips
Remove masking tape from the RH lower C-pillar
Secure clips holding rear edge of RH C-pillar lower panel to rear trunk side carpet panel

Note
3x clips, 1x magnet
Install fasteners securing C-pillar lower panel to RH parcel shelf support

Note
2x screws, T20, 2 Nm
Install RH C-pillar mid trim

Note
9x clips, Install front section first, then work around to rear
Install screw securing RH C-pillar mid trim

Note
1x screw, T20, 2 Nm
Install RH trunk sill side trim

Note
4x clips
Install LH lower C-pillar and secure clips along front edge

Note
9x clips, 1x magnet
Install bolt securing front of LH lower C-pillar

Note
1x bolt, T25, 2.5 Nm, Install new patched bolt
Install LH rear door sill trim

Note
1x patch bolt, T25, 2.5 Nm, 2x clips, Install new patch bolt
Install LH welcome plate

Note
8x clips
Remove masking tape from the LH lower C-pillar
Secure clips at rear edge of LH C-pillar lower panel

Note
2x clips, 1x magnet
Install fasteners securing C-pillar lower panel to LH parcel shelf support

Note
2x screws, T20, 2 Nm
Install LH C-pillar mid trim and secure clips

Note
9x clips, Install front section first, then work around to rear
Install screw securing LH C-pillar mid trim

Note
1x screw, T20, 2 Nm
Install LH trunk sill side trim

Note
4x clips
Fold LH 3rd row seat up

Note
Press button located on LH 3rd row seat back assembly near headrest, lift seat back into an upright position
Fold RH 3rd row seat up

Note
Press button located on LH 3rd row seat back assembly near headrest, lift seat back into an upright position
Close liftgate
Move 60 seat back and out of easy entry position
Remove tape from LH racetrack trim
Move 40 seat back and out of easy entry position

Note
Moving seat fully rearward will secure sliding plates to seat
Remove tape from RH racetrack trim
Install 2nd row floor mat
Install HEPA filter housing
Install underhood storage unit

Note
10x bolts, 10mm, 4 Nm, 10x bolts, 10mm, 7 Nm
Install frunk carpet

Note
2x connector
Install under hood aprons

Note
4x aprons
Close hood
Move RH front seat to original position
Close RH front door
Move LH front seat to original position
Calibrate falcon doors using MCU

Note
Required after 12V and FRL disconnect
Close LH front door