24/05/2023 02:28:10

Actuator - EZ Entry - 40 Track - 2nd Row Seat (7 Seat) (Remove and Replace)

Correction Code 13020022

Remove

  1. Open the RH falcon wing door.
  2. Fold the 2nd row 40 seat downwards.
  3. Release the J-hook that attaches the 2nd row 40 seat back upholstery to the seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    Fold the backrest upholstery down upon release.
    Tip: Use of the following tool(s) is recommended:
    • 6 in 90 degree tip miniature soft grip pick
  4. Unzip the 2nd row 40 seat back upholstery on the LH and RH sides of the backrest cover.
    Tip: Use of the following tool(s) is recommended:
    • 6 in 90 degree tip miniature soft grip pick
  5. Release the clips (x4) that attach the 2nd row 40 seat plastic seat back to the seat, and then remove the plastic seat back from the seat.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
  6. Release the clip that attaches the 2nd row 40 seat harness to the seat frame.
    Tip: Use of the following tool(s) is recommended:
    • Clip pry tool
  7. Relieve the tension on the metal clip by moving the 2nd row 40 seat actuator slider into the housing, and then remove and discard the metal clip from the actuator slider.
    Tip: Use of the following tool(s) is recommended:
    • Plastic trim tool
    • Small flat head screwdriver
  8. Release the 2nd row 40 seat actuator slider cable from the slider.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Use caution not to damage the cable locating plastic.
    Tip: Use of the following tool(s) is recommended:
    • Plastic trim tool
  9. Release the clips (x2) that attach the 2nd row 40 seat actuator slider to the seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use of the following tool(s) is recommended:
    • Clip pry tool
  10. Move the 2nd row 40 seat actuator slider towards the cable to relieve tension.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not kink or damage the cable.
  11. Flip the 2nd row 40 seat actuator slider vertically, use a pick to release the cable end fitting from the open slot, and then remove the slider from the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not kink or damage the cable.
    Tip: Use of the following tool(s) is recommended:
    • 6 in 90 degree tip miniature soft grip pick
  12. Disconnect the 2nd row seat 40 track EZ entry actuator connector.
  13. Remove the screws (x2) that attach the 2nd row seat 40 track EZ entry actuator to the bracket.
    Tip: Use of the following tool(s) is recommended:
    • Flex head ratchet/flex head torque wrench
    • Torx T15 socket
  14. Release the tabs (x3) that attach the 2nd row seat 40 track EZ entry actuator to the bracket, and then remove the actuator from the vehicle.
    Tip: Use of the following tool(s) is recommended:
    • Flat head screwdriver

Install

  1. Position the 2nd row seat 40 track EZ entry actuator on the vehicle, and then install the tabs (x3) that attach the actuator to the bracket.
  2. Install the screws (x3) that attach the 2nd row seat 40 track EZ entry actuator to the bracket.
    1 Nm (.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Align the screws with the actuator bracket.
    Tip: Use of the following tool(s) is recommended:
    • Flex head ratchet/flex head torque wrench
    • Ratchet/torque wrench
    • Torx T15 socket
  3. Connect the 2nd row seat 40 track EZ entry actuator connector.
  4. Position the 2nd row 40 seat actuator slider vertically on the vehicle, and then install the cable end fitting into the slider opening.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not kink or damage the cable.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use the pliers to hold the cable end fitting in place during slider installation.
    Tip: Use of the following tool(s) is recommended:
    • Needle nose long bent pliers
  5. Attach the 2nd row 40 seat actuator slider cable to the slider.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not kink or damage the cable.
  6. Install the clips (x2) that attach the 2nd row 40 seat actuator slider to the seat frame.
  7. Apply forward pressure to the 2nd row 40 seat actuator slider, and then install the new metal clip on the slider.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not deform or damage the clip.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use the flat side of the plastic trim tool to aid clip installation. Verify slider operation, and ensure proper functionality.
    Tip: Use of the following tool(s) is recommended:
    • Plastic trim tool
    • Small flat head screwdriver
  8. Install the clip that attaches the 2nd row 40 seat harness to the seat frame.
  9. Position the 2nd row 40 seat plastic seat back on the seat, and then install the clips (x4) that attach the seat back to the seat.
  10. Zip the 2nd row 40 seat back upholstery on the LH and RH sides of the backrest cover.
    Tip: Use of the following tool(s) is recommended:
    • 6in 90 degree tip miniature soft grip pick
  11. Install the J-hook that attaches the 2nd row 40 seat back upholstery to the seat.
  12. Unfold the 2nd row 40 seat into original position.
  13. Close the RH falcon wing door.