02/07/2023 19:43:59

MX Electrical - Harnesses - Main and Front Body Harnesses - Main Body Harness RHD (RR)

Correction code 17105002 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See to make sure wearing proper PPE when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT, although it has been validated. Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
  1. Drive the vehicle into a stall with a rack
  2. Open all four doors
  3. Move 2nd row seats forward using easy entry
  4. Fold 3rd row seats down
  5. Remove rear load floor
  6. Remove front lower carpet trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    Release 3rd row seat wiring harnesses from panel
  7. Fold 3rd row seats up
  8. Disconnect 3rd row seat electrical connectors
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors
  9. Lift 3rd row lower cusion
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips
  10. Set up the torchless heat induction tool
  11. Remove 3rd row seats front bolts
    Informational PurposesAn informational icon, calling your attention
    Note
    4x bolts, T45, 34 Nm, discard patch bolts
  12. Remove 3rd row rear seat bolt covers
    Informational PurposesAn informational icon, calling your attention
    Note
    Note:Plastic can be damaged/melted while applying the heat gun to the bolt inside each cover
  13. Remove 3rd row seats rear bolts
    Informational PurposesAn informational icon, calling your attention
    Note
    4x bolts, T45, 34 Nm, discard patch bolts
  14. Remove 3rd row seat from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance
  15. Chase bolts holes to clean out the old lock tight
  16. Remove 3rd row carpet from vehicle
  17. Apply tape to RH racetrack trim for protection.
  18. Apply tape to LH racetrack to avoid damage
  19. Pull back lower seal on LH B-Pillar applique and remove screws securing LH B-Pillar applique
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T25, 3 Nm
  20. Release retaining clip securing the LH B-Pillar applique to the body
    Informational PurposesAn informational icon, calling your attention
    Note
    1x retaining clip, Clip is located about 80mm below camera lens opening, Slide plastic pry tool behind LH applique seal and twist to release clip
  21. Release the LH B-Pillar applique from the body
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull applique down to release upper tab and pull applique away from body, Use caution as camera harness does not have much slack
  22. Disconnect LH B-Pillar camera connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Hold LH B-Pillar applique away from body to gain better access to the camera connector
  23. Remove LH B-Pillar applique from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Release B-pillar applique seal away from applique, Start at the top side and work around until seal is off, Do not damage seal
  24. Pull back lower seal on RH side and remove screws securing RH applique
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T25, 3 Nm
  25. Slide plastic pry tool behind RH applique seal and twist to release clip
    Informational PurposesAn informational icon, calling your attention
    Note
    Clip is located about 80mm below camera lens opening
  26. Release the LH B-Pillar applique from the body
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull applique down to release upper tab and pull applique away from body, Use caution as camera harness does not have much slack
  27. Hold RH applique away from body and disconnect camera harness connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  28. Remove LH B-Pillar applique from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Release B-pillar applique seal away from applique, Start at the top side and work around until seal is off, Do not damage seal
  29. Remove LH sunvisor bezel
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, 1x tab, Release clips, then slide bezel towards front of vehicle to release
  30. Remove LH upper A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 13mm, 8 Nm, 1x screw, T20, 2 Nm, 2x bolts, 10mm, 5 Nm, 2x connectors
  31. Move LH front seat forward
  32. Remove LH rear welcome plate
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips
  33. Remove LH rear door sill trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, T25, 2x clips, 2.5 NmDiscard bolt after removal
  34. Remove LH front lower door sill
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips, 3x datums
  35. Remove LH lower A-pillar trim
  36. Move LH front door seal away from B-pillar
  37. Remove bolts securing LH lower B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips, 2x bolts, T25, 3 Nm
  38. Remove bolts securing LH upper B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T25, 3 Nm,3x clips
  39. Remove bolt securing LH C-pillar lower trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x patch bolt, T25, 2.5 Nm, discard patch bolt
  40. Remove LH trunk sill side trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  41. Remove screw securing LH C-pillar mid trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 2 Nm
  42. Release clips securing LH C-pillar mid trim and remove
    Informational PurposesAn informational icon, calling your attention
    Note
    9x clips
  43. Remove fasteners securing LH upper C-pillar trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x patch bolt, T25, 3 Nm, 3x screws, T20, 2 Nm
  44. Release clips and remove LH upper C-pillar trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, 2 clips along front edge and 4 clips along top edge
  45. Remove RH rear welcome plate
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips
  46. Remove bolt securing RH C-pillar lower trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x patch bolt, T25, 2.5 Nm, discard patch bolt
  47. Remove RH trunk sill side trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  48. Remove screw securing RH C-pillar mid trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 2 Nm
  49. Release clips securing RH C-pillar mid trim and remove
    Informational PurposesAn informational icon, calling your attention
    Note
    9x clips
  50. Remove fasteners securing RH upper C-pillar trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T-25, 3 Nm3x screws, T-20, 2 Nm
  51. Release clips and remove RH upper C-pillar trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips
  52. Remove screws securing trunk sill panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screw, T25, 3 Nm
  53. Pull up to release clips and remove trunk sill panel
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  54. Remove clips securing rear wall trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    4x push clips
  55. Release clips and remove rear wall trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull panel towards front of vehicle and then pull up to release
  56. Remove trunk board
  57. Remove screws securing C-pillar lower panel to LH parcel shelf support
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T20, 2 Nm
  58. Release clips securing rear edge of LH C-pillar lower panel to rear trunk side carpet panel and pull top edge of C-pillar lower panel out
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, 1x magnet
  59. Release clips securing LH C-pillar lower panel along front edge and remove panel
    Informational PurposesAn informational icon, calling your attention
    Note
    9x clips, 1x magnet
  60. Release clips securing LH rear trunk side carpet panel to bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    5x push clips, One is hidden between 3rd row seat and trunk side carpet panel
  61. Remove LH trunk side carpet panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, Disconnect trunk light and 12V outlet connectors before removal, Pull rear lower corner of LH trunk side carpet panel out and downwards to remove panel
  62. Remove fasteners securing C-pillar lower panel to RH parcel shelf support
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T20, 2 Nm
  63. Release clips securing rear edge of RH C-pillar lower panel to rear trunk side carpet panel and pull top edge of C-pillar lower panel out
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, 1x magnet
  64. Release clips securing RH C-pillar lower panel along front edge and remove panel
    Informational PurposesAn informational icon, calling your attention
    Note
    9x clips, 1x magnet
  65. Release clips securing RH rear trunk side carpet panel to bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    3x push clips, One is hidden between 3rd row seat and trunk side carpet panel
  66. Pull rear lower corner of RH trunk side carpet panel out and downwards to remove panel
  67. Remove RH sunvisor bezel
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, 1x tab, Release clips, then slide bezel towards front of vehicle to release
  68. Remove RH upper A - pillar trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 13mm, 8 Nm, 1x screw, T20, 2 Nm, 2x bolts, 10mm, 5 Nm, 2x connectors
  69. Move RH front seat forward
  70. Remove RH rear door sill trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x patch bolt, T25, 2.5 Nm, 2x clips
  71. Remove RH front door sill trim
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips
  72. Remove RH lower A-pillar trim
  73. Move RH front door seal away from B-pillar
  74. Remove bolts securing RH lower B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T25, 3 Nm, 7x clips
  75. Remove bolts securing RH upper B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T25, 3 Nm,3x clips
  76. Remove front LH, RH screws securing headliner to upper body panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T20, 2 Nm, 34x clips, Lower headliner starting from the rear side
  77. Disconnect headliner harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  78. Remove headliner from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    30x clips,Recommend assistance Remove through liftgate
  79. Move 2nd row seats back using easy entry switch
  80. Remove second row floor panel 2
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, Recommend assistance, Tilt front edge upwards and remove in vertical position, Take precautions from damaging the rear of the console during removal
  81. Move both 2nd row seats forward using easy entry
  82. Remove second row floor panel 3
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips
  83. Move both 2nd row seats rearward using easy entry
    Informational PurposesAn informational icon, calling your attention
    Note
    If easy entry is not working use comfort button on the side of the seat
  84. Move RH front seat back
  85. Move LH front seat backward
  86. Lower steering column fully and move away from IP
  87. Remove IP cubby
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips
  88. Remove LH IP side trim
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips
  89. Remove LH SWD bezel
    Informational PurposesAn informational icon, calling your attention
    Note
    3x locating tabs, Slides out to the side
  90. Remove binnacle cover panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips
  91. Remove screws securing top pad at binnacle area
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T-20, 2 Nm
  92. Release top pad at leading edge, from drivers outer finisher to inner finisher
  93. Remove drivers lower IP trim
    Informational PurposesAn informational icon, calling your attention
    Note
    9x clips
  94. Release steering column cover to the instrument cluster bezel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips
  95. Remove the instrument cluster bezel from the IP carrier
    Informational PurposesAn informational icon, calling your attention
    Note
    4x screws, T20, 2.3 Nm
  96. Remove drivers inner finisher to bezel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T-20, 2 Nm
  97. Remove drivers outer finisher
    Informational PurposesAn informational icon, calling your attention
    Note
    3x screws, T-20, 2 Nm
  98. Remove RH IP side trim
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips
  99. Remove RH SWD bezel
    Informational PurposesAn informational icon, calling your attention
    Note
    3x locating tabs, Slides out to side
  100. Remove glove box upper trim
  101. Remove glove box lower trim
  102. Open glovebox
  103. Remove the glove box assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    6x screws, T20, 2.3 Nm, 3x connectors
  104. Set steering wheel column fully retracted and in the upward-most position
    Informational PurposesAn informational icon, calling your attention
    Note
    This will aid in making room for front seat removal
  105. Remove plastic seat track covers on from the front and rear seat rails
    Informational PurposesAn informational icon, calling your attention
    Note
    4x seat track covers.On older production vehicles, each seat track cover is secured with a fastener on the underside of the cover, 4x screws, PH2, 2 Nm
  106. Move LH seat forward to access to rear seat track bolts
  107. Remove LH front seat rear fasteners
    Informational PurposesAn informational icon, calling your attention
    Note
    2x patch bolts, T45P, 34 Nm, Discard after removal, Use Torchless heat induction tool to help remove bolts if necessary
  108. Move LH front seat backward
  109. Remove LH front seat front fasteners
    Informational PurposesAn informational icon, calling your attention
    Note
    2x patch bolts, T45P, 34 Nm, Discard after removal, Use Torchless heat induction tool to help remove bolts if necessary
  110. Adjust the position of the LH seat for easy removal
    Informational PurposesAn informational icon, calling your attention
    Note
    Middle of track, most upright position, seat fully up off the floor
  111. Remove all Seat track covers off the RH seat
    Informational PurposesAn informational icon, calling your attention
    Note
    4x seat track covers, On older production vehicles, each seat track cover is secured with a fastener on the underside of the cover, 4x screws, PH2, 2 Nm
  112. Remove RH front seat rear fasteners
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T45+, 34 Nm, Discard after removal, Use Torchless heat induction tool to help remove bolts
  113. Move RH front seat backward
  114. Remove RH front seat front fasteners
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T45, 34 Nm, Discard after removal, Use Torchless heat induction tool to help remove bolts
  115. Set RH Seat to a Center Position for easy removal from vehicle
  116. Use MCU screen to put the vehicle into jack mode.
  117. Place vehicle into "Tow Mode"
    Informational PurposesAn informational icon, calling your attention
    Note
    Via Controls > ''Service''
  118. Move the rack legs under the vehicle but do not lift in this step.
  119. Remove underhood aprons
    Informational PurposesAn informational icon, calling your attention
    Note
    4x aprons, LH and RH aprons have 1x clip each
  120. Remove frunk carpet
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors
  121. Remove underhood storage unit
    Informational PurposesAn informational icon, calling your attention
    Note
    10x bolts, 10mm, 4 Nm, 10x bolts, 10mm, 7 Nm
  122. Remove HEPA filter
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift up from bottom and pull out
  123. Disconnect 12V negative terminal and First Responder Loop
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 10mm, 5 Nm, 1x connector, Wait at least 2 minutes before disconnecting modules or HV components
  124. Raise the vehicle to access HV battery
  125. Remove shear platesboth sides (This helps inremoving aero shield)
    Informational PurposesAn informational icon, calling your attention
    Note
    6x screws, T-25, 3 Nm2x nuts, 15mm, 30 Nm2x bolts, 10mm, 5 Nm4x push clips
  126. Remove mid aero shield
    Informational PurposesAn informational icon, calling your attention
    Note
    20x bolts, 10mm, 4 Nm, 2x push clips
  127. Remove front bash plate extrusion
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T30, 16 Nm
  128. Remove LH ski side covers
    Informational PurposesAn informational icon, calling your attention
    Note
    14x clips, 3x covers
  129. Remove RH ski side covers
    Informational PurposesAn informational icon, calling your attention
    Note
    14x push clips, 3x covers
  130. Remove and discard remaining eight center bolts securing HV battery
    Informational PurposesAn informational icon, calling your attention
    Note
    8x bolts, E12, 38 Nm, Discard after removal
  131. Remove front four HV battery bolts
    Informational PurposesAn informational icon, calling your attention
    Note
    4x patch bolts, 13mm, 30 Nm, Discard after removal
  132. Remove and discard 21mm bolts securing front of HV battery
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 21mm, 115 Nm, Discard after removal
  133. Position battery table beneath vehicle
  134. Remove and discard RH rocker bolts
    Informational PurposesAn informational icon, calling your attention
    Note
    8x patch bolts, 13mm, 55 Nm, Discard after removal
  135. Raise vehicle and remove battery table
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance
  136. Verify no high voltage at HV rapid mate
    Informational PurposesAn informational icon, calling your attention
    Note
    Make sure to wear PPE (HV gloves, safety glasses) when working on high voltage component, Measure B+ to Ground, B- to Ground, B+ to B-, If voltage is greater than 10V, Pack contactors are not open or welded, Stop work and reach out to Service Engineering
  137. Disconnect rear subframe harness from main body harness
    Informational PurposesAn informational icon, calling your attention
    Note
    3x connectors, 1x clip
  138. Disconnect the rear parking assist harness connector and rear BLE connector
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors
  139. Disconnect tow hitch connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  140. Disconnect 12V logic connector from the charger
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  141. Release harness from body
    Informational PurposesAn informational icon, calling your attention
    Note
    4x harness clips
  142. Push rubber grommet into the vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Push the wiring harness into the vehicle from the bottom of the vehicle
  143. Remove bolts and Rear DU HV cable clips from HV battery LV logic connector bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 5 Nm2x harness clips
  144. Release the HV battery LV logic connector cover from bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips1x harness clip
  145. Remove the HV battery LV Logic connectors from bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, Make sure to remember the location of the connectors
  146. Push the logic harness through the body to the rear seat area
  147. Lower the vehicle
  148. Move the vehicle away from the hoist and place wheel chocks
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance
  149. Pry out & Remove lower, Bottom LH Seat cover Panels
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, Applicable to early production seats only
  150. Disconnect LH Seat connectors and SRS connector
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors
  151. Remove LH front seat from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend Assistance, Caution: Do not damage other components
  152. Pry out & Remove lower, Bottom RH Seat cover Panels
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips, Applicable to early production seats only
  153. Disconnect RH Seat connectors and SRS connector
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, Release red lock tab on yellow SRS connector prior to disconnecting
  154. Remove RH front seat from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend Assistance, Caution: Do not damage other components
  155. Remove rear air outlet trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  156. Disconnect the USB ports from the trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors
  157. Open the rear cup holder
  158. Remove the rear cupholder trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    Slide up to remove
  159. Close rear cup holder
  160. Release the rear center console trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips
  161. Disconnect the harnesses from the module at rear trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    6x connectors
  162. Release the LH & RH center console side trim panels
  163. Remove LH & RH center console closeout extensions
  164. Remove the front cup holder dividers, then remove the rubber mat at the base of the console
  165. Disconnect center console harness
    Informational PurposesAn informational icon, calling your attention
    Note
    4x connectors, Number of connectors may vary depending on vehicle production level
  166. Remove the bolts securing center console assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 2 Nm, 6x bolts, 10mm, 5 Nm
  167. Remove center console from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance
  168. Remove LH inner podium cover
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips
  169. Remove RH inner podium cover
  170. Release LH and RH seat harnesses from seat riser podium
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips
  171. Remove the inner seat riser fasteners and washers
    Informational PurposesAn informational icon, calling your attention
    Note
    4x bolts, T45P, 34 Nm, Discard after removal
  172. Remove inner seat riser
    Informational PurposesAn informational icon, calling your attention
    Note
    Fold carpet back to ease removal of inner seat riser
  173. Remove LH outer seat riser cover
  174. Remove LH outer seat riser
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T45, 34 Nm
  175. Remove RH outer seat riser cover
  176. Remove RH outer seat riser
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T45, 34 Nm
  177. Remove 2nd row front floor
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance
  178. Remove RH foot well cover
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, 1x connector, May need to press accelerator pedal down for more clearance
  179. Remove passenger footwell cover
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, 1x connector
  180. Remove the front carpet
    Informational PurposesAn informational icon, calling your attention
    Note
    Just pulls out
  181. Remove driver dead pedal
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 5 Nm, 2x fir tree clip
  182. Remove LH 2nd row front carpet support
    Informational PurposesAn informational icon, calling your attention
    Note
    Foam block may vary depending on vehicle configuration and production level
  183. Remove passenger foot well bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x fur tree2x fan clip
  184. Remove RH 2nd row front carpet support
    Informational PurposesAn informational icon, calling your attention
    Note
    Foam block may vary depending on vehicle configuration and production level
  185. Remove podium trim panels from LH 2nd row seat.
  186. Peel back stag beetle carpet decal from front sliding panel of the LH seat.
  187. Remove two screws securing front sliding panel to seat tracks from the LH seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T-25, 3 Nm
  188. Remove front sliding panel from seat tracks of the LH seat.
  189. Remove LH HVAC ducting between lower B pillar and upper C pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 5 Nm1x nut, 10mm, 5 Nm, Remove all sections of ducting between the B-Pillar and C-Pillar, 2 foam ducts and 2 plastic duct couplers
  190. Remove the LH bracket from the harness
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips
  191. Remove the fasteners securing LH Outer beaver dam
    Informational PurposesAn informational icon, calling your attention
    Note
    2x nuts, 10mm, 5 Nm
  192. Release the harness clips from the LH Outer beaver dam remove from the vehicle
  193. Remove podium trim panels from RH 2nd row seat
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips
  194. Peel back stag beetle carpet decal from front sliding panel of the RH seat.
  195. Remove two screws securing front sliding panel to seat tracks from the RH seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x, screws, T-25, 3 Nm
  196. Remove front sliding panel from seat tracks of the RH seat.
  197. Remove LH HVAC ducting
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 5 Nm1x nut, 10mm, 5 Nm, Remove all sections of ducting between the b pillar and c pillar, 2 foam ducts and 2 plastic duct couplers
  198. Remove the RH bracket from the harness
  199. Remove the fasteners securing the RH Outer beaver dam
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 5 Nm
  200. Release the harness clips from the RH Outer beaver dam and remove from the vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    2x harness clips
  201. Disconnect tpms module from harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  202. Disconnect the satellite radio harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  203. Disconnect the GPS radio harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  204. Release the clips that secure the harness to the closing plate
    Informational PurposesAn informational icon, calling your attention
    Note
    5x harness clips
  205. Disconnect connectors from LH and RH falcon door module
    Informational PurposesAn informational icon, calling your attention
    Note
    4x connectors
  206. Remove the bolts that secure the closing plate to the body
    Informational PurposesAn informational icon, calling your attention
    Note
    8x bolts, 10mm, 10 Nm
  207. Remove Spine plate above headliner
  208. Remove LH minion bracket from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    3x push clips
  209. Remove screws securing LH trunk bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T25, 3 Nm, 4x push clips
  210. Remove LH shock tower brace
    Informational PurposesAn informational icon, calling your attention
    Note
    9x bolts, T40, 27 Nm
  211. Release tab securing LH foam duct to plastic duct and move duct to the side
  212. Remove clips securing RH minion bracket and remove bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    3x push clips
  213. Remove the RH trunk bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T30, 7 Nm, 4x push clips
  214. Remove RH wheel house bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    9x bolts, T40, 27 Nm
  215. Remove fasteners securing ECU
    Informational PurposesAn informational icon, calling your attention
    Note
    4x nuts, 8mm, 3 Nm*Use new nuts
  216. Disconnect LH side ECU connectors
    Informational PurposesAn informational icon, calling your attention
    Note
    6x connectors
  217. Remove RH side ECU connectors
    Informational PurposesAn informational icon, calling your attention
    Note
    4x connectors
  218. Disconnect air bag connectors and clips
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  219. Remove the air bag mounting bolts
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 10 Nm, Discard after removal
  220. Release the top pad working from right to left
    Informational PurposesAn informational icon, calling your attention
    Note
    *Tape top pad chrome to prevent damage, be cautious of creases when raising.
  221. Release MCU ground strap
  222. Remove top pad from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance
  223. Remove passenger finisher from IP carrier
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T-20, 2 Nm
  224. Remove MCU from IP carrier
    Informational PurposesAn informational icon, calling your attention
    Note
    4x bolts, T-25, 6 Nm15x Electrical connections * Be careful, don’t pull out to far prior to disconnect
  225. Remove the instrument cluster
    Informational PurposesAn informational icon, calling your attention
    Note
    4x screws, T20, 2 Nm2x connectors
  226. Remove mesh grille from IP carrier
    Informational PurposesAn informational icon, calling your attention
    Note
    4x screws, T20, 2 Nm, 2x clips
  227. Remove steering wheel air bag
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T-30, 3 Nm3x connectors
  228. Remove steering wheel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 80 Nm, Mark spline for installation orientation
  229. Remove steering column module
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  230. Remove the bolt that secures the lower shaft to the steering column
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 13mm, 30 Nm,Mark the lower shaft position relative to the column
  231. Remove the steering column from the cross member
    Informational PurposesAn informational icon, calling your attention
    Note
    2x, bolts, 13mm, 30 Nm,2x nuts, 13mm, 30 Nm,2x connections
  232. Remove console outlet duct from front HVAC assembly
  233. Remove 2nd row foot ducts
  234. Disconnect the electrical connector from the dash tweeter
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  235. Remove IP carrier speakers
    Informational PurposesAn informational icon, calling your attention
    Note
    6x screws, T-20, 2 Nm3x Electrical connections
  236. Remove the screws and clips that secure the IP carrier to the dash frame
    Informational PurposesAn informational icon, calling your attention
    Note
    15x screws, T-20, 2 Nm
  237. Lift the IP carrier up, then release the clip that holds the dash tweeter electrical harness and remove IP carrier from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    *HVAC ducting will come up with itMay require 2nd technician
  238. Disconnect all electrical connectors from IP harness, including those that are connected to the PSRCM, cabin fuse boxes, and body control module (BCM)
    Informational PurposesAn informational icon, calling your attention
    Note
    Remove main harness connector under HVAC duct
  239. Remove the cross car beam from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    8x bolts, 13mm, 35 NmNote: The cross car beam is removed with the electrical harness attached*2nd technician recommended
  240. Remove connectors from the cabin fuse box
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector1x gray connector2x,brown connector1x green connector1x orange connector
  241. Remove 12v positive terminal from cabin fuse box
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 10mm, 5 Nm
  242. Remove cabin fuse box from vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    *release upper and lower tabs to remove
  243. Release frunk harness from LH main body harness connector housing
    Informational PurposesAn informational icon, calling your attention
    Note
    1x white connector 1x blue connector1x black connector
  244. Remove connector from front body module
    Informational PurposesAn informational icon, calling your attention
    Note
    1x white connector
  245. Remove ground from body under the front body module
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 13mm, 8 Nm
  246. Release harness clip from body
    Informational PurposesAn informational icon, calling your attention
    Note
    1x harness clip
  247. Disconnect the remaining frunk harness connector from RH main body harness connector housing
    Informational PurposesAn informational icon, calling your attention
    Note
    2x white connectors1x blue connector1x gray connector 1x black connector
  248. Release harness clip from connector housing
  249. Disconnect brake sensor and acceleration pedal
    Informational PurposesAn informational icon, calling your attention
    Note
    1x white connector 1x black connector
  250. Release harness clips from body
    Informational PurposesAn informational icon, calling your attention
    Note
    5x harness clips
  251. Release connector from HVAC box then Disconnect HVAC connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  252. Dissconnect PTC heat connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  253. Release harness clips from HVAC
    Informational PurposesAn informational icon, calling your attention
    Note
    3x harness clips
  254. Remove the 12V cable from the connector housing
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut 10mm, 5 Nm
  255. Remove connector housing from the body
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips 1x tab
  256. Disconnect the PRCM
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  257. Release main body harness from body
    Informational PurposesAn informational icon, calling your attention
    Note
    2x white clips 1x black
  258. Release both seat harness clips from bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x harness clips
  259. Remove ground from LH lower B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 8 Nm
  260. Disconnect LH pretensioner
    Informational PurposesAn informational icon, calling your attention
    Note
    1x yellow connector
  261. Disconnect LH B-pillar crash sensor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  262. Disconnect LH 1st row retractor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    2x yellow connectors,1x clip
  263. Disconnect LH B-pillar switch and temp sensor
    Informational PurposesAn informational icon, calling your attention
    Note
    2x black connector
  264. Disconnect LH falcon door harness from main harness
    Informational PurposesAn informational icon, calling your attention
    Note
    2x black connectors
  265. Disconnect both falcon door modules and roof USS
    Informational PurposesAn informational icon, calling your attention
    Note
    3x black connectors,1x clip
  266. Remove both grounds near falcon door modules
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 8 Nm
  267. Disconnect front camera and rear view mirror from main body harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x white connector,1x blue connector, 1x black connector
  268. Disconnect RH falcon door harness from main body harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x white connector,1x black connector
  269. Disconnect RH B-pillar switch and temp sensor
    Informational PurposesAn informational icon, calling your attention
    Note
    2x black connectors
  270. Disconnect RH 1st row retractor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    2x yellow connectors1x clip
  271. Disconnect harness from RH B-Pillar Accelerometer Sensor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  272. Disconnect RH pretensioner connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x yellow connector
  273. Remove the RH B-pillar ground from body
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 8 Nm
  274. Remove the last fastener and fur tree clips securing RH side curtain air bag
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 8 Nm2x fur tree clips
  275. Release the RH B-pillar part of the main body harness from the body
    Informational PurposesAn informational icon, calling your attention
    Note
    17x harness clips,Note routing of the harness
  276. Remove the last fastener and fur tree clips securing LH side curtain air bag
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 8 Nm2x fur tree clips
  277. Release the LH B-pillar part of the main body harness from the body*Note routing of the harness
    Informational PurposesAn informational icon, calling your attention
    Note
    23x harness clips
  278. Release the LH seat electrical connections from the protected cage and disconnect
    Informational PurposesAn informational icon, calling your attention
    Note
    1x yellow connector 1x gray connector 1x black connector
  279. Disconnect harness from LH C-pillar accelerometer sensor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  280. Release 2nd row LH main body harness up the C-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    5x harness clips *May need to release cooant hose clips
  281. Disconnect 40 seat harness
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, Release bracket for better access
  282. Disconnect harness from LH B-pillar accelerometer sensor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  283. Release 2nd row LH main body harness up the C-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    5x,harness clips *May need to release coolant hose clips
  284. Disconnect sub
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  285. Disconnect main body harness from rear HVAC harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x white connector 1x black connector
  286. Release the rear part of the RH main body harness from body and flip towards the front *Note how the harness is routed
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 8 Nm3x harness clips
  287. Pull HV logic connectors into the cabin
    Informational PurposesAn informational icon, calling your attention
    Note
    Lift up on NVH pad
  288. Disconnect main body harness from rear lift gate harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector,1x yellow connector,1x blue connector, 4x white connectors
  289. Disconnect main body harness from BCM
    Informational PurposesAn informational icon, calling your attention
    Note
    4x white connectors
  290. Disconnect main body harness from charge port light
    Informational PurposesAn informational icon, calling your attention
    Note
    1x white connector
  291. Disconnect main body harness from parking brake module
    Informational PurposesAn informational icon, calling your attention
    Note
    2x gray connectors
  292. Connect the charge port logic connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  293. Disconnect the park assist module
    Informational PurposesAn informational icon, calling your attention
    Note
    1x yellow connector 1x black connector
  294. Disconnect the D-pillar crash sensor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  295. Disconnect LH tail light
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  296. Disconnect the rear passive entry antenna
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  297. Remove ground bolt above passive entry antenna
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 8 Nm
  298. Disconnect RH tail light
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  299. Release the main body harness from the rear of the vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    6x harness clips
  300. Pull rear subframe harness into the cabin
  301. Release main body harness around the charger
    Informational PurposesAn informational icon, calling your attention
    Note
    12x harness clips
  302. Feed rear main body harness pass the rear HV cables and pass the rear frame rail
  303. Release the rear LH main body harnes bracket and flip harness towards the front of the vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    1x harness clip 1x bolt , 10mm, 8 Nm
  304. Remove main body harness from vehicle
  305. Install main body harness into vehicle
  306. Remove the tape holding the new harness bundled up
  307. Route the rear LH of the main body harness towards the back of the vehicle and secure to the body
    Informational PurposesAn informational icon, calling your attention
    Note
    1x harness clip,1x bolt, 10mm, 8 Nm
  308. Feed rear main body harness down pass the frame rail and under the HV harness
  309. Secure main body harness around the charger
    Informational PurposesAn informational icon, calling your attention
    Note
    12x harness clips
  310. Feed rear subframe harness throw the body and secure the rubber grommet
  311. Secure the main body harness to the rear of the vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    6x harness clips
  312. Connect RH tail light
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  313. Install the rear ground bolt
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 5 Nm
  314. Connect the rear passive entry antenna.
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  315. Connect LH tail light
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  316. Connect the D-pillar crash sensor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  317. Connect the park assist module
    Informational PurposesAn informational icon, calling your attention
    Note
    1x yellow connector 1x black connector
  318. Connect the charge port logic connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  319. Connect main body harness from parking brake module
    Informational PurposesAn informational icon, calling your attention
    Note
    2x gray connectors
  320. Connect main body harness from charge port light
    Informational PurposesAn informational icon, calling your attention
    Note
    1x white connector
  321. Connect main body harness to BCM
    Informational PurposesAn informational icon, calling your attention
    Note
    4x white connectors
  322. Connect main body harness from rear lift gate harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector1x yellow connector1x blue connector 4x white connector
  323. Feed HV logic connectors throw body and secure rubber gromment
    Informational PurposesAn informational icon, calling your attention
    Note
    Will need to lift up the NVH pad
  324. Route RH side of the main body harness towards the rear of the vehicle and secure to the body
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm , 8 Nm2x harness clips
  325. Connect main body harness from rear HVAC harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x white connector 1x black connector
  326. Connect sub
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  327. Secure 2nd row RH main body harness up the C-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    7x harness clips *May need to release coolant hose clips
  328. Connect RH C-pillar crash sensor
  329. Connect RH seat and install into protective cage
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector1x yellow connector 2x gray connector
  330. Secure 2nd row LH main body harness up the C-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    7x harness clips *May need to secure coolant hose clips
  331. Connect LH C-pillar crash sensor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  332. Connect LH seat and install into protective cage
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector1x yellow connector 1x gray connector
  333. Install the LH B-pillar part of the main body harness to the body
    Informational PurposesAn informational icon, calling your attention
    Note
    23x harness clips
  334. Install the last fastener and fur tree clips securing LH side curtain air bag
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 8 Nm2x fur tree clips
  335. Install the RH B-pillar part of the main body harness to the body
    Informational PurposesAn informational icon, calling your attention
    Note
    18x harness clips
  336. Install the last fastener and fur tree clips securing RH side curtain air bag
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 8 Nm2x fur tree clips
  337. Install the RH B-pillar ground to body
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 8 Nm
  338. Connect RH pretensioner
    Informational PurposesAn informational icon, calling your attention
    Note
    1x yellow connector
  339. Connect RH B-pillar crash sensor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  340. Connect RH seat belt retractor
    Informational PurposesAn informational icon, calling your attention
    Note
    2x yellow connectors
  341. Connect RH B-pillar switch and temp sensor
    Informational PurposesAn informational icon, calling your attention
    Note
    2x black connectors
  342. Connect RH falcon door harness to main body harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x white connector1x black connector
  343. Connect front camera and rear view mirror to main body harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x white connector, 1x bue connector,1x black connector
  344. Install both grounds near falcon door modules
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 8 Nm
  345. Connect both falcon door modules and roof USS
    Informational PurposesAn informational icon, calling your attention
    Note
    3x black connectors,1x clip
  346. Connect LH falcon door harness to main harness
    Informational PurposesAn informational icon, calling your attention
    Note
    2x black connectors
  347. Connect LH B-pillar switch and temp sensor
    Informational PurposesAn informational icon, calling your attention
    Note
    2x black connector
  348. Connect LH seat belt retractor
    Informational PurposesAn informational icon, calling your attention
    Note
    2x yellow connectors
  349. Connect LH B-pillar crash sensor
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  350. Connect LH pretensioner
    Informational PurposesAn informational icon, calling your attention
    Note
    1x yellow connector
  351. Install ground to lower LH B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 10mm, 8 Nm
  352. Secure both seat harness clips to bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x harness clips
  353. Secure main body harness to body
    Informational PurposesAn informational icon, calling your attention
    Note
    2x white clips 1x black
  354. Connect the PRCM
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  355. Secure connector housing to body
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, 1x tab
  356. Install ground cable to connector housing
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut 10mm, 8 Nm
  357. Install harness clips to HVAC
    Informational PurposesAn informational icon, calling your attention
    Note
    3x harness clips
  358. Connect PTC heat connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  359. Connect HVAC connector and secure to HVAC box
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector
  360. Secure harness clips to body
    Informational PurposesAn informational icon, calling your attention
    Note
    5x harness clips
  361. Connect brake sensor and acceleration pedal
    Informational PurposesAn informational icon, calling your attention
    Note
    1x white connector, 1x black connector,5x clips
  362. Install harness clip from connector housing
  363. Connect the frunk harness connector from RH main body harness connector housing
    Informational PurposesAn informational icon, calling your attention
    Note
    2x white connectors1x blue connector1x gray connector 1x black connector
  364. Install harness clip from body
    Informational PurposesAn informational icon, calling your attention
    Note
    1x harness clip
  365. Install ground from body under the front body module
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 13mm, 10 Nm
  366. Install connector from front body module
    Informational PurposesAn informational icon, calling your attention
    Note
    1x white connector
  367. install frunk harness from connector housing
    Informational PurposesAn informational icon, calling your attention
    Note
    1x white connector 1x blue connector1x black connector
  368. Install cabin fuse box to vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    *make sure tabs are fully engaged
  369. Install 12v positive terminal to the cabin fuse box
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 10mm, 5 Nm
  370. Install the main body harness connectors from the cabin fuse box
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector1x gray connector2x brown connector1x green connector1x orange connector
  371. Install cross beam to vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 13mm*Hand start a few bolts, 2nd technician recommended
  372. Install cross beam bolts
    Informational PurposesAn informational icon, calling your attention
    Note
    9x bolts, 13mm, 27Nm
  373. Re-install all IP harness connectors
    Informational PurposesAn informational icon, calling your attention
    Note
    35x connectors
  374. Secure the 2nd row passenger ducts
  375. Secure the front HVAC outlet duct.
  376. Lift IP carrier into vehicle, Install the clip that holds the dash tweeter electrical harness
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance
  377. Install the screws and clips that secure the IP carrier to the dash frame
    Informational PurposesAn informational icon, calling your attention
    Note
    15x screws, T-20, 2 Nm
  378. Install speakers to IP carrier
    Informational PurposesAn informational icon, calling your attention
    Note
    6x screws, T-20, 2 Nm3x connectors
  379. Install IP mesh grille
    Informational PurposesAn informational icon, calling your attention
    Note
    4x screws, T-20, 2 Nm2x Tree clips
  380. Install the steering column to the IP carrier
    Informational PurposesAn informational icon, calling your attention
    Note
    2x nuts, 13mm, 30 Nm2x bolts, 13mm, 30 Nm2x connectors
  381. Install shaft to lower link
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, 13mm, 30 Nm,Pay attention to the installation according to the marked position
  382. Install instrument cluster
    Informational PurposesAn informational icon, calling your attention
    Note
    4x screws, T20, 2 Nm, 3x connectors
  383. Install the MCU to the IP carrier
    Informational PurposesAn informational icon, calling your attention
    Note
    4x bolts, T-25, 7 Nm15x connectors
  384. Install drivers inner finisher to bezel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T-20, 2 Nm3x clips
  385. Install drivers outer finisher trim
    Informational PurposesAn informational icon, calling your attention
    Note
    3x screws, T-20, 2 Nm2x clips
  386. Install instrument cluster frame to dash
    Informational PurposesAn informational icon, calling your attention
    Note
    4x screws, T-20, 2 Nm
  387. Install steering column module/clock spring
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector*Replace connector locking tab
  388. Install clock spring cover to the instrument cluster bezel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips
  389. Install drivers lower IP trim
  390. Install steering wheel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, M10, 80 Nm*Replace bolt
  391. Install steering wheel air bag
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors2x screws, T-25, 7 Nm
  392. Install passenger finisher to IP carrier
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T-20, 2 Nm
  393. Set top pad in place and connect ground strap
    Informational PurposesAn informational icon, calling your attention
    Note
    Assistance required
  394. Fully seat top pad
    Informational PurposesAn informational icon, calling your attention
    Note
    27x clips
  395. Install the air bag mounting bolts
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 10 Nm
  396. Install air bag connectors & clips
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  397. Installation, and secure RH side ECU connectors
    Informational PurposesAn informational icon, calling your attention
    Note
    4x connectors
  398. Connect LH side ECU connectors
    Informational PurposesAn informational icon, calling your attention
    Note
    6x connectors
  399. Install fasteners securing ECU
    Informational PurposesAn informational icon, calling your attention
    Note
    4x nuts, 8mm, 3 Nm*Use new nuts
  400. Reinstall LH rear charger duct
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure to plastic ducts at top and bottom
  401. Install RH wheel house bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    9x bolts, T40, 27 Nm
  402. Install the RH trunk bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T30, 7 Nm4x push clips
  403. Install RH minion bracket and secure with clips
    Informational PurposesAn informational icon, calling your attention
    Note
    3x push clips
  404. Install LH shock tower brace
    Informational PurposesAn informational icon, calling your attention
    Note
    9x bolts, T40, 27 Nm
  405. Install fasteners securing LH trunk bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T25, 7 Nm, 4x push clips
  406. Install LH minion bracket and secure with the clips
    Informational PurposesAn informational icon, calling your attention
    Note
    3x push clips
  407. Position Spine plate above headliner
  408. Install the bolts that secure the closing plate to the body
    Informational PurposesAn informational icon, calling your attention
    Note
    8x bolts, 10mm, 10 Nm
  409. Install the clips that secure the harness to the closing plate
    Informational PurposesAn informational icon, calling your attention
    Note
    5x harness clips
  410. Install connectors to LH and RH falcon door module
    Informational PurposesAn informational icon, calling your attention
    Note
    4x connectors
  411. Connect the GPS radio harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  412. Connect the satellite radio harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connectors
  413. Connect TPMS module to harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  414. Place the RH side beaver dam in the vehicle and attach the wire harness clips.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x harness clips
  415. Properly seat the RH side outer beaver dam in the vehicle and secure to the body
    Informational PurposesAn informational icon, calling your attention
    Note
    2x nuts, 10mm, 10 Nm
  416. Route and Install the wire connection block for the RH side outer beaver dam
  417. Reinstall front sliding panel onto RH seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T-25, 4 Nm
  418. Install new stag beetle carpet decal onto RH seat front sliding panel.
  419. Install both podium trims on the RH outer seat.
  420. Install Lower 2nd row RH HVAC duct and cover
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 10 Nm1x nut, 10mm, 10 Nm,Install all sections of ducting between the B-Pillar and C-Pillar, 2 foam ducts and 2 plastic duct couplers
  421. Place the LH side beaver dam in the vehicle and attach the wire harness clips.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x harness clips
  422. Properly seat the LH side outer beaver dam in the vehicle and secure to the body
    Informational PurposesAn informational icon, calling your attention
    Note
    2x nuts, 10mm, 10 Nm
  423. Route and Install the wire connection block for the LH side outer beaver dam
  424. Reinstall front sliding panel onto LH seat.
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T25, 4 Nm
  425. Install new stag beetle carpet decal onto LH seat front sliding panel.
  426. Install both podium trims on the LH outer seat.
  427. Install Lower 2nd row LH HVAC duct and cover
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm,1 0 Nm1x nut, 10mm, 10 Nm, Install all sections of ducting between the B-Pillar and C-Pillar, 2 foam ducts and 2 plastic duct couplers
  428. Install RH 2nd row front floor support
    Informational PurposesAn informational icon, calling your attention
    Note
    Foam block may vary depending on vehicle configuration and production level
  429. Install passenger foot well bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x fan clips2x fur tree clips
  430. Install drivers dead pedal
    Informational PurposesAn informational icon, calling your attention
    Note
    2x nuts, 10mm, 5 Nm, 2x harness clips
  431. Lay carpet back over to drivers side
    Informational PurposesAn informational icon, calling your attention
    Note
    Just slides in
  432. Install LH 2nd row front floor support
    Informational PurposesAn informational icon, calling your attention
    Note
    Foam block may vary depending on vehicle configuration and production level
  433. Install LH foot well panel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector 2x clips
  434. Install RH foot well cover
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, 2x clips
  435. Install 2nd row front floor
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance, Replace any damaged or missing clips
  436. Install inner seat riser and secure seat harness
    Informational PurposesAn informational icon, calling your attention
    Note
    4x bolts with washers, T45+, 34 Nm, Install new bolts, 2x harness clips
  437. Install RH outer seat riser
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts with washers, T45+, 34 Nm, Install new bolts
  438. Install LH outer seat riser
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts with washers, T45+, 34 Nm, Install new bolts
  439. Install RH inner seat riser covers
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace broken clips as needed
  440. Install LH inner seat riser covers
    Informational PurposesAn informational icon, calling your attention
    Note
    Replace broken clips as needed
  441. Place center console into vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance
  442. Make connections at center console harness
    Informational PurposesAn informational icon, calling your attention
    Note
    6x connectors, Number of connectors may vary depending on vehicle production range
  443. Install the bolts securing center console assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    6x bolts, 10mm, 7 Nm, 1x screw, T20, 2 Nm
  444. Install rubber mat at the base of the console
  445. Install cup holder dividers inside console
  446. Install LH & RH center console closeout extensions
  447. Secure the center console side trim panelsLH & RH
  448. Connect module at rear console panel
    Informational PurposesAn informational icon, calling your attention
    Note
    6x connectors
  449. Install the center console back panel
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips
  450. Open rear cup holder
  451. Install the rear cup holder trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    5x tabs, Slide down to install
  452. Install USB ports into rear air outlet
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors
  453. Install the center console rear air outlet
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  454. Place RH seat into vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance
  455. Make connection at RH seat harness
    Informational PurposesAn informational icon, calling your attention
    Note
    3x connectors
  456. Install RH lower seatpanel
    Informational PurposesAn informational icon, calling your attention
    Note
    Applicable to early production seats only
  457. Place LH seat into vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Requires assistance
  458. Make connection at LH seat harness
    Informational PurposesAn informational icon, calling your attention
    Note
    3x connectors
  459. Install LH lower seatpanel
    Informational PurposesAn informational icon, calling your attention
    Note
    Applicable to early production seats only
  460. Remove the wheel chock and push the vehicle in position to be lift by hoist then reinstall wheel chock
    Informational PurposesAn informational icon, calling your attention
    Note
    Requires assistance
  461. Raise the vehicle
  462. Route the HV battery LV Logic connector for installation
    Informational PurposesAn informational icon, calling your attention
    Note
    It passes through rear DU and sway bar
  463. Install the HV battery LV Logic connectors from bracket (caution: the rapid mate bracket clip is very easy to break)
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connector clips
  464. Install the HV battery LV logic connector cover to bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    1x harness fur tree 6x clips
  465. Install bolts and Rear DU HV cable clips to HV battery LV logic connector bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    2x barrel clips, 2x bolts, 10mm, 5 Nm
  466. Secure harness to body
    Informational PurposesAn informational icon, calling your attention
    Note
    4x harness clips
  467. Connect 12V logicconnector from thecharger
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  468. Connect tow hitch connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  469. Connect the rear parking assist harness connector and rear BLE connector
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors
  470. Connect rear subframe harness to main body harness
    Informational PurposesAn informational icon, calling your attention
    Note
    3x connectors, 1x clip
  471. Move battery under vehicle
  472. Position HV battery underneath vehicle
  473. Loosely install 4 new front bolts for HV battery
    Informational PurposesAn informational icon, calling your attention
    Note
    4x patch bolts, 13mm, 30 Nm, Install new patch bolts
  474. Install LH rocker bolts hand tight
    Informational PurposesAn informational icon, calling your attention
    Note
    8x patch bolts, 13mm, 55 Nm, Install new patch bolts
  475. Install RH rocker bolts hand tight
    Informational PurposesAn informational icon, calling your attention
    Note
    8x patch bolts, 13mm, 55 Nm, Install new patch bolts
  476. Raise vehicle off of HV battery
  477. Move empty battery tableaway from vehicle
  478. Install center bolts
    Informational PurposesAn informational icon, calling your attention
    Note
    12x, bolts, E-12, 38 NmTorque in a later step
  479. Torque remaining HV battery bolts
    Informational PurposesAn informational icon, calling your attention
    Note
    8x bolts, E12, 38 Nm, 2x bolts, 21mm, 115 Nm, 4x bolts, 13mm, 30 Nm
  480. Install LH ski side covers
    Informational PurposesAn informational icon, calling your attention
    Note
    14x clips, 3x covers
  481. Install RH ski side covers
    Informational PurposesAn informational icon, calling your attention
    Note
    14x clips, 3x covers
  482. Install front bash plate extrusion
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T30, 16 Nm
  483. Install mid aero shield
    Informational PurposesAn informational icon, calling your attention
    Note
    20x bolts, 10mm, 4 Nm, 2x push clips
  484. Install shear plates
    Informational PurposesAn informational icon, calling your attention
    Note
    6x screws, T-25, 7 Nm2x nuts, 15mm, 15 Nm2x bolts, 10mm, 10 Nm4x push clips
  485. Fully lower the vehicle to the ground and move the rack legs from under the vehicle.
  486. Connect first responder loop and then 12V negative terminal
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, 1x nut, 10mm, 5 Nm
  487. Install HEPA filter housing
  488. Install underhood storage unit
    Informational PurposesAn informational icon, calling your attention
    Note
    10x bolts, 10mm, 4 Nm, 10x bolts, 10mm, 7 Nm
  489. Install frunk carpet
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors
  490. Install under hood aprons
    Informational PurposesAn informational icon, calling your attention
    Note
    4x aprons
  491. Close hood
  492. Set steering wheel column Fully Retracted and Upward Position
  493. Place vehicle out of "Tow Mode"
    Informational PurposesAn informational icon, calling your attention
    Note
    Via Controls > ''Service''
  494. Take vehicle out of jack mode
  495. Move LH seat forward and up for access to rear seat track bolts
  496. Install LH front seat rear fasteners
    Informational PurposesAn informational icon, calling your attention
    Note
    2x patch bolts, T45P, 34 Nm, Install new patch bolts
  497. Move LH front seat fully rearward
  498. Install LH front seat front fasteners
    Informational PurposesAn informational icon, calling your attention
    Note
    2x patch bolts, T45P, 34 Nm, Install new patch bolts
  499. Set LH seat to a center position or select a driver profile
  500. Install all Seat track covers for the LH seat
    Informational PurposesAn informational icon, calling your attention
    Note
    4x seat track covers, On older production vehicles, each seat track cover is secured with a fastener on the underside of the cover, 4x screws, PH2, 2 Nm
  501. Install RH front seat rear fasteners
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T45+, 34 Nm, Install new bolts
  502. Move RH seat Backward to access front seat bolts
  503. Install RH front seat front fasteners
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T45+, 34 Nm, Install new bolts
  504. Set RH Seat to a Center Position
  505. Remove all Seat track covers off the RH seat
    Informational PurposesAn informational icon, calling your attention
    Note
    4x seat track covers
  506. Move LH Seat tracks and align seat tracks, install front and rear bolts
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T45+, 34 Nm, Install new bolts
  507. Install front and rear LH seat track covers
  508. Move RH Seat tracks and align seat tracks, install front and rear bolts
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T45+, 34 Nm, Install new bolts
  509. Install all Seat track covers for the RH seat
    Informational PurposesAn informational icon, calling your attention
    Note
    4x seat track covers, On older production vehicles, each seat track cover is secured with a fastener on the underside of the cover, 4x screws, PH2, 2 Nm
  510. Move both 2nd row seats fully forward using easy entry
    Informational PurposesAn informational icon, calling your attention
    Note
    If easy entry is not working use comfort button on the side of the seat
  511. Reinstall second row floor panel
  512. Move both 2nd row seats rearward using easy entry
    Informational PurposesAn informational icon, calling your attention
    Note
    If easy entry is not working use comfort button on the side of the seat
  513. Reinstall second row floor panel 2
    Informational PurposesAn informational icon, calling your attention
    Note
    Take precautions to prevent damage to the rear of the center console, Recommend assistance, Replace any damaged or missing clips prior to installation
  514. Install 2nd row floor mat
    Informational PurposesAn informational icon, calling your attention
    Note
    Some movement of the seats may be necessary, If needed, utilize the comfort switches on second row seats
  515. Install headliner into vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance
  516. Connect headliner harness
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  517. Raise headliner and clip into place
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T20, 2 Nm, 34x clips
  518. Reinstall LH trunk side carpet panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x connectors, Reconnect trunk light and 12V outlet connectors before positioning panel. Use caution not to pinch Rear PTC harness (see picture)
  519. Install clips securing LH rear trunk side carpet panel to bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    5x push clips, One is hidden between 3rd row seat and trunk side carpet panel
  520. Verify charge port mechanical release cable is in proper position in trunk side carpet panel
  521. Install LH lower C-pillar and secure clips along front edge
    Informational PurposesAn informational icon, calling your attention
    Note
    9x clips, 1x magnet
  522. Secure clips at rear edge of LH C-pillar lower panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, 1x magnet
  523. Install screws securing C-pillar lower panel to LH parcel shelf support
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T20, 2 Nm
  524. Install LH upper C-pillar trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips
  525. Install fasteners securing LH upper C-pillar trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, T25, 3 Nm, 3x screws, T20, 2 Nm
  526. Install LH C-pillar mid trim and secure clips
    Informational PurposesAn informational icon, calling your attention
    Note
    9x clips, Install front section first, then work around to rear
  527. Install screw securing LH rear C-pillar mid trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 2 Nm
  528. Reinstall RH trunk side carpet panel
    Informational PurposesAn informational icon, calling your attention
    Note
    Reconnect trunk light connector before positioning panel,Use caution not to pinch Rear PTC harness (see picture)
  529. Reinstall clips securing RH rear trunk side carpet panel to bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    4x push clips
  530. Install RH C-pillar lower panel and secure clips along front edge
    Informational PurposesAn informational icon, calling your attention
    Note
    9x clips, 1x magnet
  531. Secure clips holding rear edge of RH C-pillar lower panel to rear trunk side carpet panel
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips, 1x magnet
  532. Install fasteners securing C-pillar lower panel to RH parcel shelf support
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T20, 2 Nm
  533. Install RH upper C-pillar trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips
  534. Reinstall fasteners securing RH upper C-pillar trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, T-25, 3 Nm2x screws, T-20, 2 Nm
  535. Install RH C-pillar mid trim
    Informational PurposesAn informational icon, calling your attention
    Note
    9x clips, Install front section first, then work around to rear
  536. Install screw securing RH C-pillar mid trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 2 Nm
  537. Reinstall rear wall trim panel
  538. Reinstall clips securing rear wall trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    4x push clips
  539. Install trunk board
  540. Reinstall trunk sill panel
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  541. Reinstall fasteners securing trunk sill panel
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T-25, 3 Nm
  542. Install LH trunk sill side trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  543. Reinstall RH rear trunk side trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips
  544. Install RH upper B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    1x nut, 13mm, 8 Nm1x screw, T-20, 2 Nm2x bolts, 10mm, 5 Nm2x Electrical connections Innstall the RH mounting fasteners from A-pillar
  545. Install RH lower B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T25, 3 Nm, 7x clips
  546. Install RH lower A-pillar trim
  547. Install RH front lower door sill
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips
  548. Install RH door seal
  549. Install RH lower B-pillar sill trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, T25, 3 Nm, 2x clips
  550. Install RH welcome plate
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips
  551. Install RH upper A-pillar
  552. Install the RH mounting fasteners from A-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, 10mm, 5 Nm1x nut, 13mm, 5 Nm 1x screw, T-20, 2 Nm
  553. Install RH sun visor bezel
  554. Install the glove box assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    3x connectors, 6x screws, T20, 2.3 Nm
  555. Install RH instrument panel lower assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    13x clips, Replace any damaged or missing clips prior to installation
  556. Install glove box lower trim
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips
  557. Install RH SWD bezel
    Informational PurposesAn informational icon, calling your attention
    Note
    3x retaining tabs, Slides into place
  558. Install RH IP end cap
    Informational PurposesAn informational icon, calling your attention
    Note
    5x clips
  559. Install LH upper B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts,T-25, 2 Nm
  560. Install LH lower B-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T25, 2 Nm, 7x clips
  561. Install LH lower A-pillar trim
  562. Install LH front lower door sill
    Informational PurposesAn informational icon, calling your attention
    Note
    7x clips
  563. Install LH front door seal
  564. Install LH lower B-pillar sill trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x bolt, T25, 2 Nm, 2x clips
  565. Install LH welcome plate
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips
  566. Install LH A-pillar
  567. Install the LH mounting fasteners from A-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts,10mm, 5 Nm1x nut, 13mm , 5 Nm 1x screw, T-20, 2 Nm
  568. Install LH sun visor bezel
  569. Install screws securing top pad at binnacle area
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T-20, 2 Nm
  570. Install binnacle cover panel
  571. Install LH SWD bezel
    Informational PurposesAn informational icon, calling your attention
    Note
    3x retaining tabs, Slides into place
  572. Install LH IP side trim
    Informational PurposesAn informational icon, calling your attention
    Note
    5x clips
  573. Install MCU cubby tray
  574. Move 2nd row seats forward using easy entry
  575. Install 3rd row carpet
    Informational PurposesAn informational icon, calling your attention
    Note
    Just slides in
  576. Place 3rd row seats inside of vehicle
    Informational PurposesAn informational icon, calling your attention
    Note
    Requires assistance
  577. Install rear 3rd row seat bolts
    Informational PurposesAn informational icon, calling your attention
    Note
    4x bolts, T-45+, 34 NmTorque in a later step
  578. Install front 3rd row seat bolts
    Informational PurposesAn informational icon, calling your attention
    Note
    4x bolts, T-45+, 34 NmTorque in a later step
  579. Torque 3rd row seat bolts
    Informational PurposesAn informational icon, calling your attention
    Note
    8x bolts, T-45+, 34 Nm
  580. Connect the 3rd row seat
    Informational PurposesAn informational icon, calling your attention
    Note
    1x black connector1x gray connector
  581. Install 3rd row seat rear cover
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, slides in
  582. Install 3rd row lower cushion
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips
  583. Make sure the 3rd seats are functioning correctly
    Informational PurposesAn informational icon, calling your attention
    Note
    End with seats fold down
  584. Fold seats up
  585. Install 3rd row rear bolt bolt covers
  586. Install rear load floor
  587. Close liftgate
  588. Move 2nd row seats back
  589. Secure applique seal to LH B-pillar applique
    Informational PurposesAn informational icon, calling your attention
    Note
    Use P-80 emulsifier to assist with seal installation
  590. Connect LH B-Pillar camera
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector, Hold LH applique away from body to gain better access to the camera connector
  591. Install LH applique by inserting top tab first, then pushing up and securing lower clip
    Informational PurposesAn informational icon, calling your attention
    Note
    Be sure top of applique in position behind upper seal
  592. Pull back lower seal on LH B-Pillar applique and install screws securing lower LH B-Pillar applique to the body
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolts, T25, 3 Nm
  593. Secure lower portion of LH B-Pillar applique seal
    Informational PurposesAn informational icon, calling your attention
    Note
    3x retaining tabs, 1 tab on either side of the lower seal, 1 tab on the bottom to secure seal to applique
  594. Inspect LH B-pillar applique seal to make sure it is fully seated
    Informational PurposesAn informational icon, calling your attention
    Note
    Adjust seal if necessary
  595. Secure LH top triangle portion of seal into position against body
  596. Secure applique seal to RH B-pillar applique
    Informational PurposesAn informational icon, calling your attention
    Note
    Use P-80 emulsifier to assist with seal installation
  597. Secure RH camera connector
  598. Install RH applique by inserting top tab first, then pushing up and securing lower clip
    Informational PurposesAn informational icon, calling your attention
    Note
    Be sure top of applique in position behind upper seal
  599. Pull back lower seal on RH side and install screws securing RH applique
    Informational PurposesAn informational icon, calling your attention
    Note
    2x bolt, T-25, 3 Nm
  600. Secure lower portion of LH B-Pillar applique seal
    Informational PurposesAn informational icon, calling your attention
    Note
    3x retaining tabs, 1 tab on either side of the lower seal, 1 tab on the bottom to secure seal to applique
  601. Inspect RH B-pillar applique seal to make sure it is fully seated
    Informational PurposesAn informational icon, calling your attention
    Note
    Adjust seal if necessary
  602. Secure RH top triangle portion of seal into position against body
  603. Remove tape from LH racetrack trim
  604. Remove the protective tape from LH racetrack trim.
  605. Move steering wheel to home location
  606. Calibrate falcon doors via UI
    Informational PurposesAn informational icon, calling your attention
    Note
    Via Controls > Calibrate, Required after 12V and FRL disconnect
  607. Close front door
  608. Drive the vehicle out of the stall