2021-05-20

Sensor - Temperature - Evaporator - Rear (Remove and Replace)

Correction code 18107702

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.
  1. Open LH front door
  2. Using MCU, open both falcon doors and liftgate
    Informational PurposesAn informational icon, calling your attention
    Note
    via Controls > Doors
  3. Move LH 2nd row seat fully forward using easy entry mode
  4. Move RH 2nd row seat fully forward using easy entry mode
  5. Remove RH welcome plate
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips
  6. Remove screw securing RH C-pillar lower trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T25, 3 Nm
  7. Fold down LH 3rd row seat
    Informational PurposesAn informational icon, calling your attention
    Note
    Press button located on LH 3rd row seat back assembly near headrest, fold seat back down towards front of vehicle into a flat position
  8. Fold down RH 3rd row seat
    Informational PurposesAn informational icon, calling your attention
    Note
    Press button located on RH 3rd row seat back assembly near headrest, fold seat back down towards front of vehicle into a flat position
  9. Remove rear load floor
  10. Remove RH trunk sill side trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  11. Remove LH trunk sill side trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  12. Remove trunk sill trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 2x patch bolts, T25, 2.5 Nm, Discard after removal
  13. Remove trunk board
  14. Remove trunk floor carpet
  15. Remove rear load floor support
    Informational PurposesAn informational icon, calling your attention
    Note
    4x push clips, 2x clips
  16. Remove screw securing RH C-pillar mid trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 2 Nm
  17. Release clips securing RH C-pillar mid trim and remove
    Informational PurposesAn informational icon, calling your attention
    Note
    9x clips
  18. Remove fasteners securing RH upper C-pillar trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T25, 3 Nm, 3x screws, T20, 2 Nm, Discard T25 fastener after removal
  19. Release clips and remove RH upper C-pillar trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips
  20. Remove fasteners securing C-pillar lower panel to RH parcel shelf support
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T20, 2 Nm
  21. Remove load floor support from RH lower C-pillar
  22. Release clips securing rear edge of RH C-pillar lower panel to rear trunk side carpet panel and pull top edge of C-pillar lower panel out
    Informational PurposesAn informational icon, calling your attention
    Note
    2x clips, 1x magnet
  23. Release clips securing RH C-pillar lower panel along front edge and remove panel
    Informational PurposesAn informational icon, calling your attention
    Note
    9x clips, 1x magnet
  24. Release clips securing RH rear trunk side carpet panel to bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    3x push clips, One is hidden between 3rd row seat and trunk side carpet panel
  25. Pull rear lower corner of RH trunk side carpet panel out and downwards to remove panel
  26. Disconnect rear evaporator temperature sensor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  27. Remove rear evaporator temperature sensor from rear HVAC assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    Twist sensor counter clockwise 1/4 turn and pull out of rear HVAC assembly
  28. Install rear evaporator temperature sensor to rear HVAC assembly
    Informational PurposesAn informational icon, calling your attention
    Note
    Insert and turn clockwise 1/4 turn to lock
  29. Connect rear evaporator temperature sensor connector
    Informational PurposesAn informational icon, calling your attention
    Note
    1x connector
  30. Reinstall RH trunk side carpet panel
    Informational PurposesAn informational icon, calling your attention
    Note
    Use caution not to pinch Rear PTC harness
  31. Reinstall clips securing RH rear trunk side carpet panel to bracket
    Informational PurposesAn informational icon, calling your attention
    Note
    3x push clips, One is hidden between 3rd row seat and trunk side carpet panel
  32. Install RH C-pillar lower panel and secure clips along front edge
    Informational PurposesAn informational icon, calling your attention
    Note
    9x clips, 1x magnet
  33. Secure clips holding rear edge of RH C-pillar lower panel to rear trunk side carpet panel
    Informational PurposesAn informational icon, calling your attention
    Note
    3x clips, 1x magnet
  34. Install fasteners securing C-pillar lower panel to RH parcel shelf support
    Informational PurposesAn informational icon, calling your attention
    Note
    2x screws, T20, 2 Nm
  35. Install trunk side nub onto RH lower C-pillar
    Informational PurposesAn informational icon, calling your attention
    Note
    3x tabs, 1x clip
  36. Install RH upper C-pillar trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    6x clips
  37. Install fasteners securing RH upper C-pillar trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T25, 3 Nm, 3x screws, T20, 2 Nm, Install new T25 fastener
  38. Install RH C-pillar mid trim
    Informational PurposesAn informational icon, calling your attention
    Note
    9x clips, Install front section first, then work around to rear
  39. Install screw securing RH C-pillar mid trim
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T20, 2 Nm
  40. Reinstall front lower carpet trim panel
    Informational PurposesAn informational icon, calling your attention
    Note
    Secure 3rd row seat wiring harnesses to panel
  41. Install rear load floor support
    Informational PurposesAn informational icon, calling your attention
    Note
    4x push clips, 2x clips
  42. Install trunk board
  43. Install rear trunk sill trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips, 2x patch bolts, T25, 2.5 Nm, Make sure to seat liftgate seal properly, Install new patch bolts
  44. Install LH trunk sill side trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  45. Install RH trunk sill side trim
    Informational PurposesAn informational icon, calling your attention
    Note
    4x clips
  46. Install rear load floor
  47. Fold 3rd row seats up
  48. Close liftgate
  49. Secure RH lower C-pillar trim to body
    Informational PurposesAn informational icon, calling your attention
    Note
    1x screw, T25, 2.5 Nm
  50. Install RH welcome plate
    Informational PurposesAn informational icon, calling your attention
    Note
    8x clips
  51. Move RH 2nd row seat out of easy entry position
  52. Move LH 2nd row seat out of easy entry position
  53. Close both rear falcon wing doors
  54. Close LH front door