26/07/2023 17:03:18

Sensor - Position - Seat Track - 2nd Row Seat - LH (Monopost) (Remove & Replace)

Correction code 13020112

Removal

  1. Open all doors and the liftgate.
  2. Move both front seats forward.
  3. Remove 2nd row floor mat.
  4. Move both 2nd row seats forward using easy entry.
  5. Apply painters tape to LH and RH racetrack to avoid damage.
  6. Remove the LH and RH rear sill panel trim (Trim - Sill Panel - Rear - LH (Remove and Replace)).
  7. Remove the LH and RH lower C-pillar trim ((refer to procedure)).
  8. Fold down the LH and RH 3rd row seats.
  9. Remove LH and RH rear trunk side garnish (Garnish - Rear Trunk - Side - LH (Remove and Replace)).
  10. Remove the LH and RH mid C-pillar trim (Trim - C-Pillar - Mid - LH (Remove and Replace)).
  11. Remove the screws (x2) that attach the C-pillar lower panel to LH and RH parcel shelf support (torque 2 Nm).
  12. Release the clips (x2) and magnet that attach the rear edge of LH and RH C-pillar lower panel to the rear trunk side carpet panel, and then pull the top edge of C-pillar lower panel out.
  13. Release the clips (x9) that attach the LH and RH C-pillar lower panel along the front edge, and then remove the panel.
  14. Put tape on the rear center console cup holder trim to prevent it from damage.
  15. Move both 2nd row seats rearward using easy entry.
  16. Release the clips (x4), tilt the front edge of the second row floor panel 3 upwards, and then remove it in vertical position.
    Informational PurposesAn informational icon, calling your attention
    Note
    Recommend assistance.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Take precautions not to damage the rear of the center console during removal.
  17. Move the LH second row seat forward.
  18. Remove the clips (x8) that attach the podium trim panels to the LH 2nd row seat.
  19. Move the LH second row seat fully backward.
  20. Peel back the 2nd row seat sliding panel carpet stag beetle carpet.
  21. Remove the screws (x2) that attach the front sliding panel to the seat tracks of the LH rear seat.
  22. Remove the front sliding panel from the seat tracks of the LH rear seat.
  23. Maneuver the seat track sensor connector out from the installed position.
  24. Disconnect the seat track position sensor connector.
  25. Remove the rivet that attaches the seat track sensor to the seat track.
    Informational PurposesAn informational icon, calling your attention
    Note
    Use a 4 mm drill to remove the top portion of the rivet.
  26. Remove the seat track position sensor from the seat track.
  27. Remove the remaining rivet from the seat frame.
  28. Vacuum all the aluminum filings.

Installation

Installation procedure is the reverse of removal, except for the following:
  1. Put the seat track position sensor in position, and then install a 3.9 mm rivet to attach the seat track position sensor to seat track.
  2. Connect the seat track position sensor connector to the seat harness.
  3. Connect a laptop with Toolbox 3 to the vehicle.
  4. Unlock the gateway. See Gateway Unlock.
  5. To disable seat install mode, in Toolbox 3, click the Actions tab, type "Seat-Install" into the search field, click PROC_BCREAR_X_SEAT-INSTALL-MODE-OFFvia Toolbox: (link), click Run, and allow the routine to complete.
  6. In Toolbox 3, click the Actions tab, type "PROC_BCS2L" in the search field, click PROC_BCS2L_R2-L_CALIBRATE-S2L-TRACKvia Toolbox: (link), click Run, and allow the routine to complete.
  7. Disconnect Toolbox and remove the laptop from the vehicle.
  8. Continue to install all parts that were previously removed.