30/05/2024 07:19:13

Liftgate Assembly (Remove and Replace)

Correction Code 10107002

  • 2024-02-01: Updated and rearranged images.
  • 2023-11-07: Fixed errors.
Part Number Description
1672283-00-A SNAP-ON, SOCKET 3/8 TORX PLUS DRIVE 16EP

Removal

  1. Remove the antenna amplifier. See Antenna Amplifier - AM/FM and RKE (Remove and Replace).
  2. Remove the liftgate speaker trim. See Grille - Speaker - Liftgate (Remove and Replace).
  3. Remove the bolts (x8) from the speaker shelf bracket (torque 2.5 Nm).
  4. Disconnect the electrical connector of the liftgate chime.
  5. Disconnect the electrical connectors of the liftgate speakers.
  6. Remove the speaker shelf bracket.
  7. Remove the liftgate glass. See Liftgate Glass (Remove and Replace).
  8. Remove the active spoiler motor (if equipped). See Motor - Active Spoiler (Remove and Replace).
  9. Remove the cinching actuator and cable. See Actuator and Cable - Cinching (Remove and Replace).
  10. Remove the LH and RH spoiler drains.
  11. Remove the liftgate applique. See Applique - Liftgate (Remove and Replace).
  12. Remove the LH and RH fog/reverse rear lights. See Light - Fog/Reverse - Rear - LH (Remove and Replace).
  13. Remove the rear view camera. See Camera - Rear View (Remove and Replace).
  14. Remove the rear license plate.
  15. Remove the LH and RH license plate lights. See Light - License Plate (Remove and Replace).
  16. Remove the screws that secure the liftgate exterior switch to the liftgate.
  17. Remove the LH and RH liftgate pinch sensors.
  18. Remove the front liftgate pinch sensor.
    Informational PurposesAn informational icon, calling your attention
    Note
    The front pinch sensor is mounted using double sided tape.
  19. Remove the LH and RH liftgate stops.
  20. Remove the LH and RH overslam bumpers.
  21. Remove the screws that secure the emergency release to the liftgate.
  22. Remove the bolts that secure the liftgate harness to the liftgate.
  23. Release the grommet from the liftgate frame, and then pull the liftgate harness through the hole in the frame.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Make sure not to scratch wire insulation.
  24. Mark the location of the bolts that attach the liftgate to the hinges.
    Informational PurposesAn informational icon, calling your attention
    Note
    This aids in reinstallation of the liftgate.
  25. Loosen the bolts that secure the liftgate to the hinges, but do not fully remove them.
  26. Use a telescoping bar to support the liftgate in the open position.
    Tip: Position the support bar against the bracket for better support.
  27. Remove the struts from the liftgate, and then lower the struts onto the rear of the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    To prevent damage, put a shop towel between the struts and the vehicle.
  28. Remove the bolts that secure the liftgate to the hinges (torque 38 Nm).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The next step requires at least 2 assistants.
  29. Remove the liftgate from the vehicle, and then place it on a padded surface

Installation

Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
If using this procedure to install an unpainted part, make sure to apply seam sealer to all seams prior to installing and painting the part. Refer to the Collision Repair manual for more information.

Installation procedure is the reverse of removal, except for the following:

  • Remove the location marks from the hinges.
  • Adjust the liftgate for proper gap and flushness.
  • For China, Japan and Korea only: Install a new motor ID label on the trunk.
  • Install a new Tesla "T" and lettering. See Rear Lettering (Remove and Replace).
  • If the vehicle is equipped with an Active Spoiler, calibrate the rear spoiler:
    1. Connect a laptop with Toolbox 3 to the vehicle.
    2. Unlock the vehicle gateway. See Gateway Unlock.
    3. In Toolbox 3, click the Actions tab, type "X_Spoiler" into the search field, click PROC_BCREAR_X_SPOILERvia Toolbox: (link), click Run, and allow the routine to complete.
    4. Disconnect Toolbox and remove the laptop from the vehicle.