2026-11-13

Bracket - B-Pillar - Upper - LH (Remove and Replace)

Correction code 15180012 FRT 0.96 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and its associated FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Remove

  1. Open the LH front door.
  2. Open all the doors and the liftgate by using the touchscreen.
  3. Remove the LH sun visor bezel. See Trim - A-Pillar - Sun Visor Bezel - LH (Remove and Replace).
  4. Remove the screws (x2) and the bolt that secure the LH A-pillar.
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
    • Torx T20 bit
  5. Move the LH A-pillar for access to the headliner.
  6. Move the LH front seat forward.
  7. Remove the LH welcome plate (8x clips).
  8. Remove the LH front lower door sill (8x clips, 3x datums).
  9. Move the LH front door seal away from the B-pillar.
  10. Remove the bolts (x2) that secure the LH lower B-pillar.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T25 bit
  11. Remove the bolts (x2) that secure the LH upper B-pillar.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T25 bit
  12. Remove the LH trunk sill side trim (4x clips).
  13. Remove the screw that secures the LH C-pillar mid trim.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T20 bit
  14. Release the clips (x9) that secure the LH C-pillar mid trim and remove the trim.
  15. Remove the LH upper C-pillar trim panel. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  16. Repeat step 3 to 15 for the RH side.
  17. Remove the headliner. See Headliner (Remove and Replace).
  18. Remove the screw that attaches the LH B-pillar racetrack to the spine racetrack.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T20 bit
  19. Remove the LH B-pillar racetrack from the vehicle (22x clips).
    Note
    Start from the bottom and work your way up.
  20. Remove the LH B-pillar upper bracket (2x clips, 4x 10 mm nuts, 1x T25 screw).
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Torx T25 bit

Install

  1. Install the LH B-pillar upper bracket (2x clips, 4x 10 mm nuts, 1x T25 screw).
    5 Nm (3.7 lbs-ft)
    3 Nm (2.2 lbs-ft)
    Note
    Torque the nuts to 5 Nm and the screw to 3 Nm.
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
    • Torx T25 bit
  2. Install the LH B-pillar racetrack (22x clips).
    Note
    Start from the top. Make sure the top of the racetrack is engaged with the spine racetrack.
  3. Make sure that the LH falcon door seal is seated behind the B-pillar racetrack.
  4. Install the screw that attaches the LH B-pillar racetrack to the spine racetrack.
    2.5 Nm (1.8 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T20 bit
  5. Install the headliner. See Headliner (Remove and Replace).
  6. Install the RH upper C-pillar trim panel. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  7. Install the RH C-pillar mid trim (9x clips).
    Note
    Install the front section first, then work around to the rear.
  8. Install the screw that secures the RH C-pillar mid trim.
    2 Nm (1.5 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T20 bit
  9. Install the RH trunk sill side trim (4x clips).
  10. Install the bolts (x2) that secure the RH upper B-pillar.
    2.5 Nm (1.8 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T25 bit
  11. Install the bolts (x2) and the clips (x7) that secure the RH lower B-pillar.
    2.5 Nm (1.8 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T25 bit
  12. Install the RH front lower door sill (7x clips).
  13. Install the RH front door seal.
  14. Install the RH welcome plate (8x clips).
  15. Move the RH front seat to the original position.
  16. Install the RH A-pillar.
  17. Install the fasteners that secure the RH A-pillar.
    5 Nm (3.7 lbs-ft)
    2.5 Nm (1.8 lbs-ft)
    Note
    Torque the 10 mm bolt to 5 Nm and the T20 screws to 2.5 Nm.
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
    • Torx T20 bit
  18. Install the RH sun visor bezel. See Trim - A-Pillar - Sun Visor Bezel - LH (Remove and Replace).
  19. Repeat step 6 to 18 for the LH side.
  20. Close all the doors and the liftgate.