Correction code 11707102 11707202 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

1. Open LH front door
2. Open LH rear door
3. Lower LH front window
4. Pull back lower seal on LH B-Pillar applique and remove screws securing LH B-Pillar applique
   Note

   2x bolts, T25, 5 Nm

   

5. Release retaining clip securing the LH B-Pillar applique to the body
   Note

   1x retaining clip, Clip is located about 80mm below camera lens opening, Slide plastic pry tool behind LH applique seal and twist to release clip

   

6. Release the LH B-Pillar applique from the body
   Note

   Pull applique down to release upper tab and pull applique away from body, Use caution as camera harness does not have much slack

   

7. Disconnect LH B-Pillar camera connector
   Note

   1x connector, Hold LH B-Pillar applique away from body to gain better access to the camera connector

   

8. Remove LH B-Pillar applique from vehicle
   Note

   Release B-pillar applique seal away from applique, Start at the top side and work around until seal is off, Do not damage seal

   

   

9. Remove upper portion of LH front primary seal
   Note

   Pull down to release from body

   

10. Release upper bright seal from LH upper bright assembly
    Note

    Begin at rear edge and move forward

    

    

11. Remove two push clips and completely remove the upper bright seal
    Note

    2x clips

    

12. Install push clips to upper bright seal
    Note

    2x clips, Step only required if new seal does not contain clips

    

13. Install lower portion of LH upper bright seal to fixed quarter glass

    

14. Continue to install LH upper bright seal
    Note

    Secure outer side first, then secure the inner side into upper bright assembly, Apply P80 to seal for lubrication

    

    

15. Secure LH upper bright seal push clips
    Note

    2x push clips

    

16. Secure applique seal to LH B-pillar applique
    Note

    Starting at the top work your way around, Fully secure seal and verify fitment, If needed use P-80 emulsifier to assist with seal installation

    

17. Connect LH B-Pillar camera
    Note

    1x connector, Hold LH applique away from body to gain better access to the camera connector

    

18. Install applique by inserting top tab first, then pushing up and securing lower clip
    Note

    1x tab, 1x clip, Be sure to place top of applique in position behind upper seal, Insert top tab first then push up and secure lower clip

    

19. Pull back lower seal on LH B-Pillar applique and install screws securing lower LH B-Pillar applique to the body
    Note

    2x bolts, T25, 5 Nm

    

20. Secure lower portion of LH B-Pillar applique seal
    Note

    3x retaining tabs, 1 tab on either side of the lower seal, 1 tab on the bottom to secure seal to applique

    

21. Inspect upper LH B-pillar applique seal to make sure it is fully seated
    Note

    Adjust seal if necessary

    

22. Secure top triangle portion of LH B-Pillar applique seal into position against body

    

23. Close LH Falcon door

    

24. Remove cubby under MCU and connect laptop to vehicle with a tethered Ethernet connection via Toolbox 2
    Note

    2x clips, 1x connector, Drive rail must be ON, Toolbox 2 program must be in current service default. Toolbox 2.0 vehicle connection will enable diagnostic mode
25. Open the "DAS2 Clear Calibration" panel
    Note

    Pathway is as follows: Panels-> Driver Assist-> DAS2 Clear Calibration
26. Clear Pillars Calibration
    Note

    Select Pillar Cameras and click on play button to Clear Calibration
27. Confirm calibration cleared
    Note

    Confirm successful clearing of the calibration for LH and RH B-pillar cameras (Do not drive to re-calibrate the cameras, performed by customer)
28. Disconnect Toolbox from vehicle and install cubby under MCU
    Note

    1x connector, 2x clips, Ensure diagnostic cables are tucked into appropriate position then engage cubby
29. Close LH front door